Home › BRAKE › BRAKE CONTROL › BRAKE ACTUATOR (w/o VSC)

BRAKE ACTUATOR (w/o VSC) > INSTALLATION

for Preparation Click here



1. INSTALL BRAKE ACTUATOR
  1. Install the brake actuator assembly with the 2 nuts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



2. INSTALL BRAKE ACTUATOR WITH BRACKET


    G024307
  1. Install the actuator with bracket with the 3 bolts.

    Torque:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }

    NOTICE:
    Be careful not to damage the brake tubes and wire harness.



    F045470E01
  1. Using SST, connect each brake tube to correct positions of the actuator with bracket, as shown in the illustration.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

  1. Connect the brake actuator connector assembly.



3. INSTALL AIR CLEANER ASSEMBLY WITH HOSE


4. FILL RESERVOIR WITH BRAKE FLUID


G024304

Fluid:
SAE J1703 or FMVSS No. 116 DOT3

NOTICE:
Perform the procedure after confirming the sub-tank at the upper of the master cylinder assembly is filled enough.



5. BLEED BRAKE MASTER CYLINDER SUB-ASSEMBLY

NOTICE:
When the air is bled from the master cylinder (3rd chamber), be sure to run the engine.

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air out of the master cylinder.

  1. Run the engine at idle.

  1. Connect the vinyl tube to the brake caliper bleeder plug.

  1. Open the brake caliper bleeder plug or wheel cylinder bleeder plug.



    F045198
  1. Depress the brake pedal several times, then loosen the master cylinder (3rd chamber) bleeder plug with the pedal held down (*3).

  1. At the point when the fluid stops coming out, tighten the master cylinder (3rd chamber) bleeder plug, then release the brake pedal (*4).

  1. Repeat (*3) and (*4) several times until the air in the master cylinder is bled out.

  1. Tighten the master cylinder (3rd chamber) bleeder plug .

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. Tighten the brake caliper bleeder plug or wheel cylinder bleeder plug.

    Torque:
    Disc:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }
    Drum:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }



6. BLEED BRAKE LINE


    C080826
  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, then loosen the bleeder plug with the pedal depressed (*5).

  1. At the point when fluid stops coming out, tighten the bleeder plug, then release the brake pedal (*6).

  1. Repeat (*5) and (*6) several times until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug completely.

    Torque:
    Disc:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }
    Drum:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. Repeat the above procedure to bleed the air out of the brake line for each wheel.



7. CHECK BRAKE FLUID LEAKAGE


8. CHECK FLUID LEVEL IN RESERVOIR
  1. Check the fluid level and add fluid, if necessary.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3



9. CONNECT BATTERY NEGATIVE TERMINAL


10. PERFORM INITIALIZATION


11. CHECK BRAKE ACTUATOR WITH TECHSTREAM

HINT:
Click here.