Home › BODY › SEAT › REAR NO. 2 SEAT ASSEMBLY (for Power Seat Type LH Side)

REAR NO. 2 SEAT ASSEMBLY (for Power Seat Type LH Side) > REASSEMBLY

for Preparation Click here



1. INSTALL NO. 2 SEAT LEG SUB-ASSEMBLY


    B126840E02
  1. Install the No. 2 seat leg sub-assembly with the 3 bolts and 2 nuts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

    NOTICE:
    Tighten the bolts and nuts in the order shown in the illustration.

  1. Install the 3 clamps.



2. INSTALL NO. 2 SEAT CUSHION FRAME SUB-ASSEMBLY


3. INSTALL NO. 2 SEAT CUSHION SPRING ASSEMBLY


4. INSTALL NO. 2 SEAT CUSHION STOPPER


5. INSTALL REAR SEAT WIRE


6. INSTALL NO. 2 SEAT CUSHION PAD


7. INSTALL NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY


  1. Using hog ring pliers, install the No. 2 seat cushion cover sub-assembly to the No. 2 seat cushion pad with 10 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.



    B128435E01



8. INSTALL NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY WITH PAD


9. INSTALL REAR SEAT COVER


10. INSTALL REAR SEAT BELT ASSEMBLY INNER


    B126857
  1. Install the rear seat belt assembly inner with the bolt.

    Torque:
    44 N*m{ 449 kgf*cm , 33 ft.*lbf }



11. INSTALL REAR NO. 2 SEAT BELT ASSEMBLY INNER


    B126856
  1. Install the rear No. 2 seat belt assembly inner with the bolt.

    Torque:
    44 N*m{ 449 kgf*cm , 33 ft.*lbf }



    B126855E01
  1. Using hog ring pliers, install 2 new hog rings.

    NOTICE:
    Be careful not to damage the cover.



12. INSTALL REAR NO. 2 SEAT LAP BELT ASSEMBLY CENTER WITH INNER


    B126854
  1. Install the rear No. 2 seat lap belt assembly center with inner with the bolt and washer.

    Torque:
    44 N*m{ 449 kgf*cm , 33 ft.*lbf }



13. INSTALL REAR POWER SEAT SWITCH


14. INSTALL RECLINING REMOTE CONTROL LEVER BEZEL


15. INSTALL NO. 2 SEATBACK FRAME SUB-ASSEMBLY


    B126851E01
  1. Install the No. 2 seatback frame sub-assembly with the 4 bolts.

    Torque:
    44 N*m{ 449 kgf*cm , 33 ft.*lbf }

    NOTICE:
    1. Tighten the bolts in the following order:
    2. Temporarily tighten bolt (1).
    3. Temporarily tighten bolt (2).
    4. Fully tighten bolt (3).
    5. Fully tighten bolt (4).
    6. Fully tighten bolt (1).
    7. Fully tighten bolt (2).



16. INSTALL FOLD SEAT CONTROL ECU


17. INSTALL NO. 2 SEATBACK PAD


18. INSTALL NO. 2 SEATBACK COVER SUB-ASSEMBLY


  1. Using hog ring pliers, install the No. 2 seatback cover sub-assembly to the No. 2 seatback pad with 10 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.



    B128434E01



19. INSTALL NO. 2 SEATBACK COVER SUB-ASSEMBLY WITH PAD


20. INSTALL REAR NO. 2 SEAT HEADREST SUPPORT ASSEMBLY RH


21. INSTALL REAR NO. 2 SEAT HEADREST SUPPORT ASSEMBLY LH


22. INSTALL REAR SEAT HEADREST ASSEMBLY


23. INSTALL REAR SEAT RECLINING COVER RH


24. INSTALL REAR SEAT RECLINING COVER LH


25. INSTALL REAR NO. 2 SEAT COVER BEZEL