Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION ANTENNA

NAVIGATION ANTENNA > INSTALLATION

for Preparation Click here



1. INSTALL NAVIGATION ANTENNA ASSEMBLY


2. INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY


  1. Using a torque wrench, install the bolt <B>.


    B066708E03

    Torque:
    20 N*m{ 204 kgf*cm , 14 ft.*lbf }



3. INSTALL SHIFT LEVER ASSEMBLY


    B069776
  1. Using a torque wrench, install the 4 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 12.6 ft.*lbf }



4. INSTALL DEFROSTER NOZZLE OPENING PLATE NO.1


5. INSTALL FRONT NO.2 SPEAKER ASSEMBLY


6. INSTALL FRONT NO.1 SPEAKER ASSEMBLY


7. INSTALL INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY NO.2


8. INSTALL INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


9. INSTALL FRONT PILLAR GARNISH RH


10. INSTALL FRONT PILLAR GARNISH LH


11. INSTALL INTEGRATION CONTROL & PANEL ASSEMBLY


12. INSTALL NAVIGATION RECEIVER ASSEMBLY


13. INSTALL STEREO COMPONENT SPEAKER ASSEMBLY


14. INSTALL INSTRUMENT CLUSTER FINISH PANEL GARNISH


15. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY LOWER CENTER


16. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY CENTER


17. INSTALL FLOOR SHIFT POSITION INDICATOR HOUSING ASSEMBLY


18. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY


19. INSTALL INSTRUMENT CLUSTER FINISH PANEL CENTER NO.2


20. INSTALL INSTRUMENT CLUSTER FINISH PANEL CENTER NO.1


21. INSTALL FLOOR CARPET COVER CENTER RH


22. INSTALL FLOOR CARPET COVER CENTER LH


23. INSTALL INSTRUMENT PANEL REGISTER ASSEMBLY NO.3


24. INSTALL INSTRUMENT PANEL REGISTER ASSEMBLY NO.1


25. INSTALL INSTRUMENT SIDE PANEL RH


26. INSTALL INSTRUMENT SIDE PANEL LH


27. INSTALL INSTRUMENT PANEL BOX NO.2


28. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY


29. INSTALL GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY


30. INSTALL INSTRUMENT PANEL SAFETY PAD INSERT SUB-ASSEMBLY NO.1


31. INSTALL INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LOWER LH


32. INSTALL COWL SIDE TRIM BOARD RH


33. INSTALL COWL SIDE TRIM BOARD LH


34. INSTALL FRONT DOOR SCUFF PLATE RH


35. INSTALL FRONT DOOR SCUFF PLATE LH


36. INSTALL COMBINATION METER ASSEMBLY


37. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


38. INSTALL WINDSHIELD WIPER SWITCH ASSEMBLY


39. INSTALL HEADLIGHT DIMMER SWITCH ASSEMBLY


40. INSTALL SPIRAL CABLE SUB-ASSEMBLY


41. INSTALL STEERING COLUMN COVER


42. ADJUST SPIRAL CABLE SUB-ASSEMBLY
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) terminal is disconnected.

    CAUTION:
    After removing the terminal, wait for at least 90 seconds before starting the operation.



    H042773
  1. Rotate the spiral cable counterclockwise slowly by hand until it feels firm.

    NOTICE:
    Do not turn the spiral cable by the airbag wire harness.



    H042774E01
  1. Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.

    NOTICE:
    Do not turn the spiral cable by the airbag wire harness.

    HINT:
    The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.



43. INSTALL STEERING WHEEL ASSEMBLY
  1. Align the matchmarks on the steering wheel assembly and steering main shaft assembly.

  1. Install the steering wheel assembly set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Connect the connector.



44. INSTALL HORN BUTTON ASSEMBLY


    H042675
  1. Support the steering pad with one hand as shown in the illustration.

  1. Connect the 2 connectors to the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Connect the horn connector.

  1. Confirm that the circumference groove of the "torx" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.

  1. Using a "torx" socket wrench (T30), tighten the 2 "torx" screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }



45. INSTALL STEERING WHEEL COVER LOWER NO.2


46. INSTALL STEERING WHEEL COVER LOWER NO.3


47. CONNECT BATTERY NEGATIVE TERMINAL


48. INSPECT HORN BUTTON ASSEMBLY


    H042649
  1. With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:

    1. Cuts, minute cracks or marked discoloration on the steering pad top surface or in the grooved portion.

  1. Make sure that the horn sounds.

    HINT:
    If the horn does not sound, inspect the horn system (Click here).



49. INSPECT SRS WARNING LIGHT
  1. Inspect the SRS warning light (Click here).