Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION ANTENNA

NAVIGATION ANTENNA > REMOVAL

for Preparation Click here



1. BOLT, SCREW AND NUT TABLE


  1. The bolts, the screws and the nuts, which are necessary for installation and removal of the instrument panel are shown in the illustration below with alphabets.


    B066709E01



2. DISCONNECT BATTERY NEGATIVE TERMINAL

CAUTION:
Wait for 90 seconds after disconnecting the cable to prevent the airbag working.



3. REMOVE STEERING WHEEL COVER LOWER NO.2


4. REMOVE STEERING WHEEL COVER LOWER NO.3


5. REMOVE HORN BUTTON ASSEMBLY


    H042695E01
  1. Using a "torx" socket wrench (T30), loosen the 2 "torx" screws until the groove along the screw circumference catches on the screw case.



    H042674
  1. Pull out the steering pad from the steering wheel assembly and support the steering pad with one hand as shown in the illustration.

    NOTICE:
    When removing the steering pad, do not pull the airbag wire harness.

  1. Disconnect the horn connector.

  1. Disconnect the 2 connectors from the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Remove the steering pad.



6. REMOVE STEERING WHEEL ASSEMBLY


    F044997E02
  1. Remove the steering wheel assembly set nut.

  1. Put matchmarks on the steering wheel assembly and main shaft assembly.

  1. Using SST, remove the steering wheel assembly.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)



7. REMOVE STEERING COLUMN COVER


    H042796
  1. Remove the 2 screws and the steering column cover.



8. REMOVE HEADLIGHT DIMMER SWITCH ASSEMBLY


    I035549E01
  1. Disconnect the connector.

  1. Release the claw fitting and remove the headlight dimmer switch assembly.



9. REMOVE WINDSHIELD WIPER SWITCH ASSEMBLY
  1. Disconnect the connector.



    I035788E01
  1. Using a screwdriver, disengage the claw and pull out the windshield wiper switch assembly.

    NOTICE:
    The claw will be broken if pressed hard.

    HINT:
    Tape up the screwdriver tip before use.



10. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    B066068E01
  1. Remove the 2 clips.

  1. Pull the instrument cluster finish panel sub-assembly rearward to remove it.



11. REMOVE COMBINATION METER ASSEMBLY


    B066069E01
  1. Remove the 4 screws <C>.

  1. Pull out the combination meter assembly, then disconnect the connectors.



12. REMOVE FRONT DOOR SCUFF PLATE RH


    B066491E01
  1. Using a screwdriver, disengage the 3 clips and 2 claws, and remove the scuff plate.

    HINT:
    Tape the screwdriver tip before use.



13. REMOVE FRONT DOOR SCUFF PLATE LH


14. REMOVE COWL SIDE TRIM BOARD RH


    B069503E01
  1. Using a screwdriver, disengage the 2 clips and claw, and remove the trim board.

    HINT:
    Tape the screwdriver tip before use.



15. REMOVE COWL SIDE TRIM BOARD LH


16. REMOVE INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LOWER LH


    B066070E01
  1. Remove the 2 bolts <A>.

  1. Disconnect the hood lock control cable assembly.

  1. Disengage the 2 claws and 3 clips, and then remove the instrument panel finish panel sub-assembly lower LH.

  1. Disconnect the connectors.



17. REMOVE INSTRUMENT PANEL SAFETY PAD INSERT SUB-ASSEMBLY NO.1


    B066071E01
  1. Remove the 4 bolts <A> and instrument panel safety pad insert sub-assembly No. 1.

  1. Disconnect the connector.



18. REMOVE GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY


    B066072
  1. Disengage the claw, and remove the glove compartment door stopper sub-assembly.



19. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


    B066073E01
  1. Push the right side wall and then push the left wall to release the stoppers.



    B066074
  1. Pull the glove compartment door sub-assembly rearward to remove it.



20. REMOVE INSTRUMENT PANEL BOX NO.2


    B066075E01
  1. Disengage the 2 claws and the 4 clips, and remove the instrument panel box No. 2.



21. REMOVE INSTRUMENT SIDE PANEL LH


    B066076E01
  1. Disengage the 5 claws by pulling up the edge of the instrument side panel LH from the rear of the vehicle.

  1. Remove the instrument side panel LH.



22. REMOVE INSTRUMENT SIDE PANEL RH


23. REMOVE INSTRUMENT PANEL REGISTER ASSEMBLY NO.1


    B066700E01
  1. Disengage the claw and 4 clips, and then remove the instrument panel register assembly No. 1.



24. REMOVE INSTRUMENT PANEL REGISTER ASSEMBLY NO.3


25. REMOVE FLOOR CARPET COVER CENTER LH


    B066701E01
  1. Remove the clip on the floor carpet cover center LH.

  1. Depress the edge of the floor carpet cover center LH around the claws to disengage the two claws under beneath of the floor carpet cover center LH.

  1. Slightly sliding the floor carpet cover center LH to the front of the vehicle, detach the two claws from the instrument cluster finish panel sub-assembly lower center at the floor carpet cover center LH.

  1. Remove the floor carpet cover center LH.



26. REMOVE FLOOR CARPET COVER CENTER RH


27. REMOVE INSTRUMENT CLUSTER FINISH PANEL CENTER NO.1
  1. Using a moulding remover, disengage the 3 clips as shown in the illustration.

  1. Disconnect the connector and remove the instrument cluster finish panel center No. 1.



28. REMOVE INSTRUMENT CLUSTER FINISH PANEL CENTER NO.2


29. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    B066702
  1. Remove the floor shift lever knob sub-assembly.



30. REMOVE FLOOR SHIFT POSITION INDICATOR HOUSING ASSEMBLY


    B068514E01
  1. Disengage the 4 claws, and remove the floor shift position indicator housing assembly.



31. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY CENTER


    B066703E01
  1. Remove the screw <C>.

  1. Disengage the 5 clips and the claw from the lowest part on the instrument cluster finish panel assembly center in order.

  1. Disconnect the connectors at the instrument cluster finish panel sub-assembly lower center, and then remove the instrument cluster finish panel assembly center.



32. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY LOWER CENTER


    B066704E01
  1. Remove the 2 clips on both sides.

  1. Remove the 3 screws <C> and 3 bolts <A>.

  1. Pull the instrument cluster finish panel sub-assembly lower center rearward to remove it.

  1. Disconnect the connector.



33. REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH


    B067325E01
  1. Insert the edge of a moulding remover between the instrument cluster finish panel garnish and the radio receiver from the top center, and then lean the moulding remover toward the front of the vehicle to raise the instrument cluster finish panel garnish.

  1. Disengage the claw on the top of the instrument cluster finish panel garnish and the two clips from the radio receiver.



    B067326
  1. Pull up the instrument cluster finish panel garnish to the front of the vehicle to disengage the 5 claws at the bottom of the instrument cluster finish panel garnish.

  1. Remove the instrument cluster finish panel garnish.



34. REMOVE STEREO COMPONENT SPEAKER ASSEMBLY


    I035563
  1. Remove the 2 screws and stereo component speaker assembly.

  1. Disconnect the connector.



35. REMOVE NAVIGATION RECEIVER ASSEMBLY


36. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY


    I035724
  1. Remove the 4 screws, and release the integration control & panel assembly.

  1. Disconnect the connectors and remove the integration control & panel assembly.



37. REMOVE FRONT PILLAR GARNISH RH


    B066495
  1. w/ curtain shield airbag:
    Using a screwdriver, disengage the cover of the pillar garnish and bolt.

    HINT:
    Tape the screwdriver tip before use.



    B066494E01
  1. Using a screwdriver, disengage the 3 clips and claw and remove the pillar garnish.

    HINT:
    Tape the screwdriver tip before use.



    B065292E07
  1. Pull the garnish upward and remove it from the instrument panel.

  1. w/ curtain shield airbag:
    Protect the curtain shield airbag LH.

    1. Thoroughly cover the airbag with cloth or nylon of 700 mm (27.56 in.) x 120 mm (4.72 in.) and fix the ends of the cover with adhesive tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with the protection cover as soon as the pillar garnish is removed.



38. REMOVE FRONT PILLAR GARNISH LH


39. REMOVE INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    B067327E01
  1. Using a screwdriver, disengage the 2 clips and remove the instrument panel speaker panel sub-assembly.



40. REMOVE INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY NO.2


41. REMOVE FRONT NO.1 SPEAKER ASSEMBLY


    I035562
  1. Remove the 2 screws and front No. 1 speaker assembly.

  1. Disconnect the connector.



42. REMOVE FRONT NO.2 SPEAKER ASSEMBLY


43. REMOVE DEFROSTER NOZZLE OPENING PLATE NO.1


    B068519
  1. Using a screwdriver, disengage the 6 claws and remove the defroster nozzle opening plate No. 1.

  1. Disconnect the connector.



44. SEPARATE SHIFT LEVER ASSEMBLY


    B069776
  1. Remove the 4 bolts and separate the shift lever assembly.



45. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
  1. Remove the 4 bolts <A> <B> and 2 screws <C> and a nut <E>.

  1. Disconnect the connectors.



  1. Remove the instrument panel sub-assembly w/ passenger airbag assembly.


    B066708E01



46. REMOVE NAVIGATION ANTENNA ASSEMBLY


    I035575
  1. Release the 3 clamps and remove the 2 screws and the navigation antenna assembly.