Home › DRIVE LINE › DIFFERENTIAL › REAR DIFFERENTIAL CARRIER

REAR DIFFERENTIAL CARRIER > DISASSEMBLY

for Preparation Click here



1. REMOVE REAR DIFFERENTIAL CARRIER COVER


    C098113
  1. Remove the 8 bolts from the carrier cover.

  1. Using a brass bar and a hammer, separate the carrier cover from rear differential carrier assembly.

  1. Remove the breather plug from the rear differential carrier cover.



    C067695
  1. Remove the bolt and oil deflector from the carrier cover.



2. FIX REAR DIFFERENTIAL CARRIER ASSEMBLY


3. INSPECT RUNOUT OF DIFFERENTIAL RING GEAR


    F001238
  1. Using a dial gauge, check the runout of the ring gear.

    Maximum runout:
    0.07 mm (0.0028 in.)

    If the runout is greater than the maximum, replace the ring gear with a new one.



4. INSPECT DIFFERENTIAL RING GEAR BACKLASH


    C067698
  1. Using a dial gauge, check the backlash of the ring gear.

    Backlash:
    0.13 to 0.18 mm (0.0051 to 0.0071 in.)

    If the backlash is not within the specification, adjust the side bearing preload or repair as necessary.



5. INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION


    F001259
  1. Coat 3 or 4 teeth at 3 different positions on the ring gear with red lead primer.

  1. Hold the companion flange firmly and rotate the ring gear in both directions.



  1. Inspection the tooth contact pattern.


    SA01653E05

    If the teeth are not contacting properly, use following table to select proper washer for correction.

    SA01586E01

    Washer thickness:

    Thickness mm (in.)
    Thickness mm (in.)
    Thickness mm (in.)
    2.26 to 2.28 (0.0890 to 0.0898)
    2.41 to 2.43 (0.0949 to 0.0957)
    2.56 to 2.58 (0.1008 to 0.1016)
    2.29 to 2.31 (0.0902 to 0.0909)
    2.44 to 2.46 (0.0961 to 0.0969)
    2.59 to 2.61 (0.1020 to 0.1028)
    2.32 to 2.34 (0.0913 to 0.0921)
    2.47 to 2.49 (0.0972 to 0.0980)
    2.62 to 2.64 (0.1031 to 0.1039)
    2.35 to 2.37 (0.0925 to 0.0933)
    2.50 to 2.52 (0.0984 to 0.0992)
    2.65 to 2.67 (0.1043 to 0.1051)
    2.38 to 2.40 (0.0937 to 0.0945)
    2.53 to 2.55 (0.0996 to 0.1004)
    2.68 to 2.70 (0.1055 to 0.1063)



6. INSPECT DIFFERENTIAL PINION AND SIDE GEAR BACKLASH


    F001240
  1. Using a dial gauge, check the backlash of the side gear while holding 1 pinion gear toward the differential case.

    Backlash:
    0.05 to 0.20 mm (0.0020 to 0.0079 in.)

    If the backlash is not within the specification, install the 2 side gear thrust washers of differential thickness .

    HINT:
    Measure the backlash of the side gear with the side gear shaft installed.



7. INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


    F001237E08
  1. Using a dial gauge, measure the runout of the companion flange vertically and horizontally.

    Maximum runout:
    0.10 mm (0.0039 in.)



8. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD


    SA02352
  1. Using a torque wrench, measure the preload of the drive pinion.

    Torque:
    0.6 to 0.9 N*m{ 6 to 9 kgf*cm , 5.2 to 7.8 in.*lbf }



9. INSPECT TOTAL PRELOAD


    SA02352
  1. Using a torque wrench, measure the total preload.

    Torque:
    0.3 to 0.5 N*m{ 3 to 5 kgf*cm , 2.6 to 4.3 in.*lbf }



10. REMOVE REAR DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY


    C067701
  1. Using needle nose pliers, remove the 2 snap rings from the 2 side gear shafts.

  1. Remove the 2 side gear shafts.



11. REMOVE REAR DIFFERENTIAL SIDE GEAR SHAFT DUST COVER


    C068113
  1. Using a screwdriver and a hammer, remove the side gear shaft dust cover.



12. REMOVE REAR DIFFERENTIAL SIDE GEAR SHAFT SEAL OIL


    C097804E01
  1. Using SST, remove the 2 oil seals from the housing.

    SST
    09308-00010  



13. REMOVE REAR DRIVE PINION NUT


    G024173E02
  1. Using SST and a hammer, unstake the staked part of the nut.

    SST
    09930-00010  



    SA02349E08
  1. Using SST to hold the flange, remove the nut.

    SST
    09330-00021  



14. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


    R011391E04
  1. Using SST, remove the companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)



15. REMOVE REAR DIFFERENTIAL DUST DEFLECTOR


    F040564E10
  1. Using SST and a press, remove the dust deflector.

    SST
    09950-60010   (09951-00360)
    09950-70010   (09951-07150)
    09950-00020  



16. REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL


    SA02348E06
  1. Using SST, remove the oil seal from the differential carrier.

    SST
    09308-10010  



17. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER


18. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


    Z000641E06
  1. Using SST, remove the front tapered roller bearing from the drive pinion.

    SST
    09556-22010  



19. REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER


20. REMOVE DIFFERENTIAL CASE ASSEMBLY


    F003753E01
  1. Align matchmarks on the bearing cap and differential carrier.

  1. Remove the 4bolts and 2 bearing caps.



    C067710E02
  1. Using SST and a hammer, remove the 2 plate washers.

    SST
    09504-22011  

    HINT:
    Measure the thickness of the plate washers and note it down.



    C068107
  1. Remove the differential case assembly and the 2 bearing outer races from the differential carrier.

    HINT:
    Tag the 2 bearing outer races races to show the location for reassembly.



21. REMOVE DIFFERENTIAL DRIVE PINION
  1. Remove the differential drive pinion.



22. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING


    R010668E05
  1. Using SST and a press, remove the rear bearing from the drive pinion.

    SST
    09950-00020  

    HINT:
    If either the drive pinion or ring gear is damaged, replace both as a set.

  1. Remove the plate washer.



23. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


    C051361
  1. Using a brass bar and a hammer, remove the front bearing (outer race) from the carrier.



24. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING


    C051362
  1. Using a brass bar and a hammer, remove the rear bearing (outer race) from the carrier.



25. REMOVE DIFFERENTIAL RING GEAR


    F003755E01
  1. Align matchmarks on the ring gear and differential case.

  1. Using a screwdriver and a hammer, unstake the 4 lock plates.

  1. Remove the 8 ring gear set bolts and 4 lock plates.

  1. Using a plastic hammer, tap on the ring gear to separate it from the differential case.



26. INSPECT DIFFERENTIAL CASE ASSEMBLY


    C068112
  1. Install the differential case to the differential carrier.

  1. Install the right and left bearing caps with the 4 bolts.

    Torque:
    79 N*m{ 800 kgf*cm , 58 ft.*lbf }

  1. Using a dial gauge, measure the differential case runout.

    Maximum case runout:
    0.07 mm (0.0028 in.)

  1. Remove the differential case.



27. REMOVE REAR DIFFERENTIAL CASE BEARING LH


    F040345E05
  1. Using SST, remove the case bearing (LH) from the differential case.

    SST
    09950-40011   (09951-00240, 09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
    09950-60010   (09951-00360)



28. REMOVE REAR DIFFERENTIAL CASE BEARING RH


    F040346E02
  1. Using SST, remove the case bearing (RH) from the differential case.

    SST
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
    09950-60010   (09951-00360)



29. REMOVE REAR DIFFERENTIAL PINION SHAFT


    C063262
  1. Using a pin punch (5 mm) and a hammer, remove the straight pin.



    ZK01879E04
  1. Remove the differential pinion shaft. (A)

  1. Remove the 2 differential pinion gears. (B)

  1. Remove the 2 differential pinion thrust washers. (C)

  1. Remove the 2 side gears. (D)

  1. Remove the 2 side gear thrust washers. (E)