Home › BRAKE › PARKING BRAKE › PARKING BRAKE CABLE

PARKING BRAKE CABLE > INSTALLATION

for Preparation Click here



1. INSTALL PARKING BRAKE CABLE ASSEMBLY NO.3
  1. Install the parking brake cable LH guide to the parking brake cable assembly No. 3.

  1. Connect the parking brake cable No. 3 to the parking brake cable equalizer.



  1. Install the parking brake cable No. 3 with the 3 bolts and button.


    F045028E01

    Torque:
    Bolt (A):
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
    Bolt (B):
    8 N*m{ 82 kgf*cm , 71 in.*lbf }



2. CONNECT PARKING BRAKE CABLE ASSEMBLY NO.3


    F045063E01
  1. Install the parking brake cable No. 3 with the 2 bolts to the backing plate.

    Torque:
    8 N*m{ 82 kgf*cm , 71 in.*lbf }



3. APPLY HIGH TEMPERATURE GREASE (for Drum Type)


    F042693
  1. Apply high temperature grease to the shoe attached surface of backing plate.



4. INSTALL REAR BRAKE SHOE (for Drum Type)
  1. Apply high temperature grease to the adjusting bolt.

  1. Install the rear brake strut set with the shoe return spring.



    C094672
  1. Using a pliers, install the rear brake strut set, parking brake reaction lever and parking brake shoe lever LH with the 2 new C-washers.



    F042688
  1. Using a needle-nose pliers, connect the parking brake cable No. 3 to the parking brake shoe lever LH.



    F045069E01
  1. Using SST, install the rear brake shoe, pin, shoe hold down spring and shoe hold down spring cup.

    SST
    09718-00010  



5. INSTALL FRONT BRAKE SHOE (for Drum Type)
  1. Install the rear brake automatic adjust lever LH, automatic adjust lever spring and parking brake shoe strut LWR to the front brake shoe.



    F045068E01
  1. Using SST, install the front brake shoe, pin, shoe hold down spring and shoe hold down spring cup.

    SST
    09718-00010  



    F042698
  1. Install the tension spring to the front brake shoe and rear brake shoe.



    C094674
  1. Using a needle-nose pliers, install the return spring.



    F045067E01
  1. Using SST, install the shoe return spring to the front brake shoe.

    SST
    09921-00010  



6. CHECK REAR DRUM BRAKE INSTALLATION (for Drum Type)


  1. Check that each part is installed properly.


    F045346E01

  1. Measure the brake drum inside diameter and the diameter of the brake shoes. Check that difference between the diameter is the correct shoe clearance.

    Shoe clearance:
    0.5 mm (0.020 in.)

    NOTICE:
    There should be no oil or grease adhering to the friction surfaces of the shoe lining and the drum.



7. INSTALL REAR BRAKE DRUM SUB-ASSEMBLY (for Drum Type)


8. ADJUST REAR DRUM BRAKE SHOE CLEARANCE (for Drum Type)
  1. Temporarily install the hub nuts.

  1. Remove the hole plug, and turn the adjuster and expand the shoe until the drum locks.



    F040023E05
  1. Using a screwdriver, back off the adjuster 15 notches.

  1. Install the hole plug.



9. INSPECT PARKING BRAKE PEDAL TRAVEL (for Drum Type)
  1. Slowly depress the parking brake pedal all the way, and count the number of clicks.

    Parking brake pedal travel:
    3 to 5 clicks at 294 N (30 kgf, 66.0 lbf)



10. ADJUST PARKING BRAKE PEDAL TRAVEL (for Drum Type)
  1. Depress the parking brake pedal 3 notches to make a room for the procedure, and loosen the lock nut.

  1. Return the parking brake pedal to the original position.

  1. Turn the adjusting nut until the parking brake pedal travel corrects.



    F045024E01
  1. Depress the parking brake pedal 3 notches to make a room for the procedure, and tighten the lock nut.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. Return the parking brake pedal to the original position.

  1. Check whether the parking brake drags or not.

  1. When operating the parking brake pedal, check that the parking brake pedal indicator light goes on.



11. APPLY HIGH TEMPERATURE GREASE (for Disc Type)
  1. Apply the high temperature grease to the surface on which the shoe and backing plate attach.



12. INSTALL PARKING BRAKE SHOE ASSEMBLY LH NO.2 (for Disc Type)


    R000310
  1. Using needle-nose pliers, connect the parking brake cable No. 3 to the parking brake shoe lever.

  1. Install the parking brake shoe assembly LH No. 2 with the shoe hold-down compression spring pin No. 2, shoe hold-down compression spring and 2 cups.



13. INSTALL PARKING BRAKE SHOE ADJUSTING SCREW SET (for Disc Type)


14. INSTALL PARKING BRAKE SHOE STRUT LH (for Disc Type)


15. INSTALL PARKING BRAKE SHOE ASSEMBLY LH NO.1 (for Disc Type)
  1. Install the parking brake shoe assembly LH No. 1 with the shoe hold-down compression spring pin No. 1, shoe hold-down compression spring and 2 cups.



    F012039
  1. Install the tension spring and 2 shoe return tension springs.



16. CHECK PARKING BRAKE INSTALLATION (for Disc Type)


  1. Check that each part is installed properly.


    F045276E01

    NOTICE:
    No oil or grease should be adhered to the friction surface of the shoe lining and disc.



17. INSTALL REAR DISC (for Disc Type)


    F041543E13
  1. Aligning the matchmarks, install the rear disc.

    HINT:
    Select the installation position where the disc has the minimum runout.



18. ADJUST PARKING BRAKE SHOE CLEARANCE (for Disc Type)


    F040026E02
  1. Temporarily install the hub nuts.

  1. Remove the hole plug, and turn the adjuster and expand the shoes until the disc locks.

  1. Contract the shoe adjuster until the disc can rotate smoothly.

    Standard:
    Return 8 notches

  1. Check that the brake disc rotates smoothly.

  1. Install the hole plug.



19. CONNECT REAR DISC BRAKE CALIPER ASSEMBLY LH (for Disc Type)
  1. Install the disc brake cylinder assembly rear LH with the 2 bolts.

    Torque:
    34 N*m{ 350 kgf*cm , 25 ft.*lbf }



20. INSTALL REAR WHEEL

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }



21. INSTALL PARKING BRAKE PEDAL TRAVEL
  1. Slowly depress the parking brake pedal all the way, and count the number of clicks.

    Parking brake pedal travel:
    3 to 5 clicks at 294 N (30 kgf, 66.0 lbf)



22. ADJUST PARKING BRAKE PEDAL TRAVEL
  1. Depress the parking brake pedal 3 notches to make a room for the procedure, and loosen the lock nut.

  1. Return the parking brake pedal to the original position.

  1. Turn the adjusting nut until the parking brake pedal travel corrects.



    F045024E01
  1. Depress the parking brake pedal 3 notches to make a room for the procedure, and tighten the lock nut.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. Return the parking brake pedal to the original position.

  1. Check whether the parking brake drags or not.

  1. When operating the parking brake pedal, check that the parking brake pedal indicator light goes on.