Home › BRAKE › PARKING BRAKE › PARKING BRAKE CABLE

PARKING BRAKE CABLE > REMOVAL

for Preparation Click here


HINT:
For the parking brake cable assembly No. 2, perform the same procedure to the parking brake cable assembly No. 3.



1. REMOVE REAR WHEEL


2. REMOVE REAR BRAKE DRUM SUB-ASSEMBLY (for Drum Type)
  1. Release the parking brake lever, and remove the rear brake drum.

    HINT:
    If the rear brake drum cannot be removed easily, perform the following procedure.



    F040009
  1. Remove the hole plug and insert a screwdriver through the hole in the backing plate, and hold the automatic adjusting lever away from the adjuster.

  1. Using another screwdriver, reduce the brake shoe adjuster by turning the adjusting wheel.



3. REMOVE FRONT BRAKE SHOE (for Drum Type)


    C094667E01
  1. Using SST, remove the shoe return spring from the front brake shoe.

    SST
    09921-00010  



    C094668
  1. Using a needle-nose pliers, remove the return spring.



    F045068E01
  1. Using SST, remove the shoe hold down spring cup, shoe hold down spring and pin.

    SST
    09718-00010  

  1. Remove the parking brake shoe strut LWR.

  1. Remove the tension spring and front brake shoe.

  1. Remove the automatic adjust lever spring and rear brake automatic adjust lever LH from the front brake shoe.



4. REMOVE REAR BRAKE SHOE (for Drum Type)


    F045069E01
  1. Using SST, remove the shoe hold down spring cup, shoe hold down spring and pin.

    SST
    09718-00010  



    F042688
  1. Using a needle-nose pliers, disconnect the parking brake cable No. 3 and remove the rear brake shoe.



    C094672
  1. Using a screwdriver, remove the 2 C-washers, parking brake shoe lever, parking brake reaction lever LH and rear brake strut set.



5. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY LH (for Disc Type)

HINT:
Do not disconnect the flexible hose from the brake caliper.



6. REMOVE REAR DISC (for Disc Type)


    F041543E13
  1. Make matchmarks on the rear disc and the axle hub.

  1. Remove the rear disc.



7. REMOVE PARKING BRAKE SHOE ASSEMBLY LH NO.1 (for Disc Type)


    C064523E02
  1. Using needle-nose pliers, remove the 2 shoe return tension springs.



    F012039
  1. Disconnect the tension spring from the parking brake shoe assembly LH No. 1.

  1. Slide out the parking brake shoe assembly LH No. 1 and remove the parking brake shoe assembly LH No. 1.

  1. Remove the shoe hold-down compression spring, 2 cups and shoe hold-down compression spring pin No. 1.



8. REMOVE PARKING BRAKE SHOE ADJUSTING SCREW SET (for Disc Type)


9. REMOVE PARKING BRAKE SHOE STRUT LH (for Disc Type)


10. REMOVE PARKING BRAKE SHOE ASSEMBLY LH NO.2 (for Disc Type)


    R000310
  1. Disconnect the return spring from the parking brake shoe assembly LH No. 2 and remove the tension spring.

  1. Slide out the parking brake shoe assembly LH No. 2.

  1. Remove the shoe hold-down compression spring, 2 cups and shoe hold-down compression spring pin No. 2.

  1. Using needle-nose pliers, disconnect the parking brake cable No. 3 from the parking brake shoe lever and remove the parking brake shoe assembly LH No. 2.



11. SEPARATE PARKING BRAKE CABLE ASSEMBLY NO.3


    F045063E01
  1. Remove the 2 bolts, and disconnect the parking brake cable No. 3 from the backing plate.



12. REMOVE PARKING BRAKE CABLE ASSEMBLY NO.3
  1. Remove the 3 bolts and the button to disconnect the parking brake cable No. 3 from the body.

  1. Disconnect the parking brake cable No. 3 from the parking brake equalizer, and remove the parking brake cable No. 3.



  1. Remove the parking brake cable LH guide from the parking brake cable assembly No. 3.


    F045028