Home › BRAKE › BRAKE › FRONT BRAKE

FRONT BRAKE > INSTALLATION

for Preparation Click here


HINT:
Install the RH side using the same procedure as the LH side.



1. INSTALL FRONT DISC BRAKE CYLINDER SLIDE BUSH


    C190377E01
  1. Apply a light layer of lithium soap base glycol grease to the contact surface of the front disc brake cylinder slide pin (No. 2).

  1. Install a new front disc brake cylinder slide bush to the end of the front disc brake cylinder slide pin (No. 2).



2. INSTALL FRONT DISC BRAKE CYLINDER SLIDE PIN


    C190378E02
  1. Apply a light layer of lithium soap base glycol grease to the sliding and sealing surfaces of the front disc brake cylinder slide pin (No. 1) and front disc brake cylinder slide pin (No. 2).



    F045565E06
  1. Install the front disc brake cylinder slide pin (No. 1) and front disc brake cylinder slide pin (No. 2) to the front disc brake cylinder mounting LH.



3. INSTALL FRONT DISC BRAKE CYLINDER MOUNTING LH


    F045344
  1. Install the front disc brake cylinder mounting with the 2 bolts.

    Torque:
    107 N*m{ 1,090 kgf*cm , 79 ft.*lbf }



4. INSTALL FRONT DISC BRAKE PAD SUPPORT PLATE
  1. Install the front disc brake pad support plate (No. 1) and front disc brake pad support plate (No. 2) to the front disc brake cylinder mounting LH.



5. INSTALL ANTI SQUEAL SHIM KIT FRONT

NOTICE:
If necessary, replace the anti squeal shim kit when replacing the brake pad.

  1. Apply disc brake grease to each anti squeal shim.

  1. Install the anti squeal shims on each pad.

  1. Install the pad wear indicator plate facing upward, and install each pad.



6. INSTALL DISC BRAKE PAD KIT FRONT (PAD ONLY)
  1. Install the disc brake pad kit front to the front disc brake cylinder mounting LH.

    NOTICE:
    There should be no oil or grease on the friction surfaces of the pads and the disc.



7. REMOVE FRONT DISC BRAKE CYLINDER ASSEMBLY LH


    C097868
  1. Install the front disc brake cylinder sub-assembly with the 2 bolts.

    Torque:
    34 N*m{ 350 kgf*cm , 25 ft.*lbf }

  1. Install a 2 new gaskets and flexible hose with the union bolt.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }

    HINT:
    Install the flexible hose lock securely in the lock hole in the disc brake cylinder.



8. FILL RESERVOIR WITH BRAKE FLUID


G024304

Fluid:
SAE J1703 or FMVSS No. 116 DOT3

NOTICE:
Perform the procedure after confirming the sub-tank at the upper of the master cylinder assembly is filled enough.



9. BLEED BRAKE MASTER CYLINDER

NOTICE:
When the air is bled from the master cylinder (3rd chamber), be sure to run the engine.

HINT:
If the master cylinder has been disassembled or if the reservoir becomes empty, bleed the air out of the master cylinder.

  1. Run the engine at idle.

  1. Connect the vinyl tube to the brake caliper bleeder plug.

  1. Open the brake caliper bleeder plug or wheel cylinder bleeder plug.



    F045198
  1. Depress the brake pedal several times, then loosen the master cylinder (3rd chamber) bleeder plug with the pedal held down (*3).

  1. At the point when the fluid stops coming out, tighten the master cylinder (3rd chamber) bleeder plug, then release the brake pedal (*4).

  1. Repeat (*3) and (*4) several times until the air in the master cylinder is bled out.

  1. Tighten the master cylinder (3rd chamber) bleeder plug .

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. Tighten the brake caliper bleeder plug or wheel cylinder bleeder plug.

    Torque:
    Disc:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }
    Drum:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }



10. BLEED BRAKE LINE


    C080826
  1. Connect the vinyl tube to the bleeder plug.

  1. Depress the brake pedal several times, then loosen the bleeder plug with the pedal depressed (*5).

  1. At the point when fluid stops coming out, tighten the bleeder plug, then release the brake pedal (*6).

  1. Repeat (*5) and (*6) several times until all the air in the fluid is completely bled out.

  1. Tighten the bleeder plug completely.

    Torque:
    Disc:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }
    Drum:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. Repeat the above procedure to bleed the air out of the brake line for each wheel.



11. BLEED BRAKE ACTUATOR (w/ VSC)

NOTICE:
After bleeding the air from the brake system, if the height or feel of the brake pedal cannot be obtained, bleed the air from the brake actuator assembly with the Techstream by following the procedure below.

  1. Depress the brake pedal more than 20 times with the ignition switch off.

  1. Connect the Techstream to the DLC3, then turn the ignition switch to the ON position.

    NOTICE:
    Do not start the engine.

  1. Turn the Techstream on and select "AIR BLEEDING" on the screen.

    NOTICE:
    1. Refer to the Techstream operator's manual for farther details.
    2. Perform air bleeding by following the steps displayed on the Techstream.

  1. Perform air bleeding according to "Step 1: Increase" on the Techstream display.

    NOTICE:
    Make sure that the master cylinder reservoir tank does not become empty of brake fluid.


    1. Connect a vinyl tube to either one of the bleeder plugs.

    2. Depress the brake pedal several times, then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (*7).

    3. When fluid stops coming out, tighten the bleeder plug, then release the brake pedal (*8).

    4. Repeat (*7) and (*8) until all the air in the fluid is completely bled out.

    5. Tighten the bleeder plug completely.

      Torque:
      Disc:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf }
      Drum:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    6. Repeat the above procedures for the rest of the wheels to bleed the air from the brake line.

  1. Bleed the air from the suction line according to "Step 2: Inhalation" on the Techstream display.

    NOTICE:
    1. Bleed the suction line by following the steps displayed on the Techstream.
    2. Make sure that the master cylinder reservoir tank does not become empty of brake fluid.


    1. Connect a vinyl tube to the bleeder plug at the right front wheel or the right rear wheel and loosen the bleeder plug.

    2. Operate the brake actuator assembly to perform air bleeding using the Techstream (*9).

      NOTICE:
      1. The operation stops automatically in 4 seconds.
      2. At this time, be sure to release the brake pedal.

    3. Check that the operation has stopped by referring to the Techstream display and tighten the bleeder plug (*10).

    4. Repeat (*9) and (*10) until all the air in the fluid is completely bled out.

    5. Tighten the bleeder plug completely.

      Torque:
      Disc:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf }
      Drum:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    6. For the rest of the wheels, perform air bleeding in the same way as stated in the above procedure.

  1. Bleed the air from the pressure reduction line according to "Step 3: Decrease" on the Techstream display.

    NOTICE:
    1. Bleed the pressure reduction line by following the steps displayed on the Techstream.
    2. Make sure that the master cylinder reservoir tank does not become empty of brake fluid.


    1. Connect a vinyl tube to either one of the bleeder plugs.

    2. Loosen the bleeder plug (*11).

    3. Using the Techstream, operate the brake actuator assembly, completely depress the brake pedal, and hold it.

      NOTICE:
      1. The operation stops automatically in 4 seconds. When performing this procedure continuously, an interval of at least 20 seconds is required.
      2. When the operation is completed, the brake pedal goes down slightly. This is a normal phenomenon when the solenoid opens.
      3. During this procedure, the pedal seems heavy, but completely depress it so that the brake fluid comes out from the bleeder plug.
      4. Be sure to keep the brake pedal depressed. Never depress and release the pedal repeatedly.

    4. Tighten the bleeder plug, then release the brake pedal (*12).

    5. Repeat (*11) to (*12) until all the air in the fluid is completely bled out.

    6. Tighten the bleeder plug completely.

      Torque:
      Disc:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf }
      Drum:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    7. Repeat the above procedures for the rest of the brakes to bleed the air from the brake line.

  1. Bleed the air from the brake line again according to "Step 4: Increase" on the Techstream display.

    NOTICE:
    1. Bleed the brake line by following the steps displayed on the Techstream.
    2. Make sure that the master cylinder reservoir tank does not become empty of brake fluid.


    1. Connect a vinyl tube to either one of the bleeder plugs.

    2. Depress the brake pedal several times, then loosen the bleeder plug connected to the vinyl tube with the pedal depressed (*13).

    3. When fluid stops coming out, tighten the bleeder plug, then release the brake pedal (*14).

    4. Repeat (*13) and (*14) until all the air in the fluid is completely bled out.

    5. Tighten the bleeder plug completely.

      Torque:
      Disc:
      8.3 N*m{ 85 kgf*cm , 73 in.*lbf }
      Drum:
      11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    6. Repeat the above procedures for each brake to bleed the air from the brake line.

  1. Finish "AIR BLEEDING" on the Techstream and turn off the Techstream.

  1. Disconnect the Techstream from the DLC3.

  1. Turn the ignition switch to the OFF position.



12. CHECK FLUID LEVEL IN RESERVOIR
  1. Check the fluid level and add fluid, if necessary.

    Fluid:
    SAE J1703 or FMVSS No. 116 DOT3



13. INSPECT FOR BRAKE FLUID LEAK


14. INSTALL FRONT WHEEL

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }