Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > TERMINALS OF ECU

for Preparation Click here



JUNCTION CONNECTOR


  1. Junction connector


    C132298E18


    with VSC 
    Junction Connector
    Wiring Color
    Connect to
    J17-5 (CANH)
    B
    Distance control ECU(*1)
    J17-16 (CANL)
    W
    Distance control ECU(*1)
    J17-6 (CANH)
    B
    Network gateway ECU
    J17-17 (CANL)
    W
    Network gateway ECU
    J17-7 (CANH)
    B
    CAN Junction connector
    J17-18 (CANL)
    W
    CAN Junction connector
    J17-8 (CANH)
    B
    DLC3
    J17-19 (CANL)
    W
    DLC3
    J17-10 (CANH)
    B
    Skid control ECU
    J17-21 (CANL)
    W
    Skid control ECU
    J17-11 (CANH)
    B
    Steering angle sensor
    J17-22 (CANL)
    W
    Steering angle sensor

    HINT:
    *1: with Dynamic laser cruise control


    without VSC 
    Junction Connector
    Wiring Color
    Connect to
    J17-6 (CANH)
    B
    Network gateway ECU
    J17-17 (CANL)
    W
    Network gateway ECU
    J17-7 (CANH)
    B
    ECM
    J17-18 (CANL)
    W
    ECM
    J17-8 (CANH)
    B
    DLC3
    J17-19 (CANL)
    W
    DLC3



  2. CAN junction connector (with VSC)


    C136775E02


    with VSC 
    CAN Junction Connector
    Wiring Color
    Connect to
    J49-1 (CANH)
    B
    Yaw rate sensor
    J49-2 (CANL)
    W
    Yaw rate sensor
    J49-3 (CANH)
    B
    Junction connector
    J49-7 (CANL)
    W
    Junction connector
    J49-4 (CANH)
    B
    ECM
    J49-6 (CANL)
    W
    ECM



  3. The connection diagram of the components which are connected to the CAN junction connector.


    C161434E01


DLC3
C125062E05
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance 
    Terminals
    Wiring Color
    Condition
    Specified Condition
    D1-6 (CANH) - D1-14 (CANL)
    B - W
    Ignition switch off
    54 to 69 Ω
    D1-14 (CANL) - D1-4 (CG)
    W - W-B
    Ignition switch off
    200 Ω or higher
    D1-6 (CANH) - D1-4 (CG)
    B - W-B
    Ignition switch off
    200 Ω or higher
    D1-14 (CANL) - D1-16 (BAT)
    W - B-O
    Ignition switch off
    6 kΩ or higher
    D1-6 (CANH) - D1-16 (BAT)
    B - B-O
    Ignition switch off
    6 kΩ or higher


ECM

G035613E31

  1. Disconnect the connector from the ECM.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance 
    Terminals
    Wiring Color
    Condition
    Specified Condition
    E5-33 (CANH) - E5-34 (CANL)
    B - W
    Ignition switch off
    108 to 132 Ω
    E5-34 (CANL) - E11-1 (E1)
    W - BR
    Ignition switch off
    200 Ω or higher
    E5-33 (CANH) - E11-1 (E1)
    B - BR
    Ignition switch off
    200 Ω or higher
    E5-34 (CANL) - E4-3 (BATT)
    W - B-W
    Ignition switch off
    6 kΩ or higher
    E5-33 (CANH) - E4-3 (BATT)
    B - B-W
    Ignition switch off
    6 kΩ or higher


NETWORK GATEWAY ECU

C129903E03

  1. Disconnect the connector from the netwark gateway ECU.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance 
    Terminals
    Wiring Color
    Condition
    Specified Condition
    G4-17 (CA1H) - G4-18 (CA1L)
    B - W
    Ignition switch off
    108 to 132 Ω
    G4-18 (CA1L) - G4-24 (GND)
    W - B-W
    Ignition switch off
    200 Ω or higher
    G4-17 (CA1H) - G4-24 (GND)
    B - B-W
    Ignition switch off
    200 Ω or higher
    G4-18 (CA1L) - G4-10 (BATT)
    W - W-L
    Ignition switch off
    6 kΩ or higher
    G4-17 (CA1H) - G4-10 (BATT)
    B - W-L
    Ignition switch off
    6 kΩ or higher


SKID CONTROL ECU WITH ACTUATOR

F049377E18

  1. Disconnect the connector from the skid control ECU with actuator.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance 
    Terminals
    Wiring Color
    Condition
    Specified Condition
    S3-11 (CANH) - S3-25 (CANL)
    B - W
    Ignition switch off
    54 to 69 Ω
    S3-25 (CANL) - S3-32 (GND1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    S3-11 (CANH) - S3-32 (GND1)
    B - W-B
    Ignition switch off
    200 Ω or higher
    S3-25 (CANL) - S3-31 (+BS)
    W - W
    Ignition switch off
    6 kΩ or higher
    S3-11 (CANH) - S3-31 (+BS)
    B - W
    Ignition switch off
    6 kΩ or higher


STEERING ANGLE SENSOR

F100891E09

  1. Disconnect the connector from the steering angle sensor.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance 
    Terminals
    Wiring Color
    Condition
    Specified Condition
    S9-10 (CANH) - S9-9 (CANL)
    B - W
    Ignition switch off
    54 to 69 Ω
    S9-9 (CANL) - S9-2 (ESS)
    W - W-B
    Ignition switch off
    200 Ω or higher
    S9-10 (CANH) - S9-2 (ESS)
    B - W-B
    Ignition switch off
    200 Ω or higher
    S9-9 (CANL) - S9-3 (BAT)
    W - W-L
    Ignition switch off
    6 kΩ or higher
    S9-10 (CANH) - S9-3 (BAT)
    B - W-L
    Ignition switch off
    6 kΩ or higher


YAW RATE SENSOR
G026641E27
  1. Disconnect the connector from the yaw rate sensor.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance 
    Terminals
    Wiring Color
    Condition
    Specified Condition
    Y1-3 (CANH) - Y1-2 (CANL)
    B - W
    Ignition switch off
    54 to 69 Ω
    Y1-2 (CANL) - Y1-1 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    Y1-3 (CANH) - Y1-1 (GND)
    B - W-B
    Ignition switch off
    200 Ω or higher
    Y1-2 (CANL) - D1-16 (BAT)
    W - B-O
    Ignition switch off
    6 kΩ or higher
    Y1-3 (CANH) - D1-16 (BAT)
    B - B-O
    Ignition switch off
    6 kΩ or higher


DISTANCE CONTROL ECU

C148251E01

  1. Disconnect the connector from the distance control ECU.



  2. C125062E06
  3. Measure the resistance according to the value(s) in the table below.

    Standard resistance 
    Terminals
    Wiring Color
    Condition
    Specified Condition
    D2-8 (CANH) - D2-9 (CANL)
    B - W
    Ignition switch off
    54 to 69 Ω
    D2-9 (CANL) - D2-12 (GND)
    W - BR
    Ignition switch off
    200 Ω or higher
    D2-8 (CANH) - D2-12 (GND)
    B - BR
    Ignition switch off
    200 Ω or higher
    D2-9 (CANL) - D1-16 (BAT)
    W - B-O
    Ignition switch off
    6 kΩ or higher
    D2-8 (CANH) - D1-16 (BAT)
    B - B-O
    Ignition switch off
    6 kΩ or higher