Home › BODY › ENGINE HOOD / DOOR › POWER BACK DOOR SYSTEM

POWER BACK DOOR SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK POWER BACK DOOR ECU

B068464E08

  1. Disconnect the P13 and P14 ECU connectors, and check the voltage or resistance of each terminal of the wire harness side connectors.

    Terminal No.
    Wiring Color
    Condition
    Specified Condition
    P14-2 (B) - Body ground
    B-R - Body ground
    Constant
    10 to 14 V
    P13-10 (ECUB) - Body ground
    W-L - Body ground
    Constant
    10 to 14 V
    P13-9 (IG) - Body ground
    B-R - Body ground
    Ignition switch OFF → ON
    0 V → 10 to 14 V
    P14-8 (GND) - Body ground
    W-B - Body ground
    Constant
    Below 1 Ω
    P13-6 (MSW) - P13-5 (MSE)
    L - W
    Power back door main switch OFF → ON
    Below 1 Ω → 10 kΩ or higher
    P13-3 (HSW) - Body ground
    G-B - Body ground
    Back door opener switch OFF → ON
    10 kΩ or higher → Below 1 Ω
    P13-14 (OSL) - P13-15 (OSE)
    G-W - Y-B
    Power back door touch sensor LH
    FREE → PRESSED
    Approx. 1 kΩ → Less than 100 Ω
    P13-16 (OSR) - P13-15 (OSE)
    BR-Y - Y-B
    Power back door touch sensor RH
    FREE → PRESSED
    Approx. 1 kΩ → Less than 100 Ω
    P13-22 (MPX1) - Body ground
    R-L - Body ground
    BEAN line
    10 kΩ or higher
    If the result is not as specified, there may be a malfunction on the wire harness side.

  2. Reconnect the ECU connectors, and check the voltage of each terminal of the connectors.

    Terminal No.
    Wiring Color
    Condition
    Specified Condition
    P14-4 (CTYO) - Body ground
    G-W - Body ground
    Back door CLOSED → OPEN
    10 to 14 V → Below 1 V
    P13-2 (BZR+) - Body ground
    O - Body ground
    1. Buzzer that notifies the start of opening sounds at 2 cycles of approx. 0.5 sec. when A*1 or B*2 switch is pressed so that the power back door starts opening operation
    2. All conditions necessary for warning buzzer to sound*3 are met →
      Any condition necessary for warning buzzer to stop*4 is met
    1. 10 to 14 V
      (2 cycles of approx. 0.5 sec.)
    2. 10 to 14 V (a cycle of approx. 0.3 sec.) → 0 V
    P13-1 (BZR-) - Body ground
    LG - Body ground
    P13-26 (DSV) - P13-23 (DSG)
    Y - GR
    Constant
    10 to 14 V
    P13-25 (DS1) - P13-23 (DSG)
    BR - GR
    Back door fully closed and A or B switch turned ON →
    Back door in opening operation →
    Back door fully open
    0 V →
    Alternating between 10 to 14 V and 0 V→
    0 V
    P13-24 (DS2) - P13-23 (DSG)
    L-B - GR
    P14-1 (BD+) - Body ground
    B - Body ground
    Back door fully closed and A or B switch turned ON →
    Back door in opening operation →
    Back door fully open
    0 V →
    10 to 14 V →
    0 V
    P14-3 (BD-) - Body ground
    W - Body ground
    Back door fully open and A or B switch turned ON →
    Back door in closing operation →
    Back door fully closed
    0 V →
    10 to 14 V →
    0 V
    P14-7 (CL+) - Body ground
    P - Body ground
    Back door fully open and A or B switch turned ON →
    Back door in closing operation →
    Back door fully closed
    0 V →
    Alternating between 10 to 14 V and 0 V→
    0 V
    P14-6 (CL-) - Body ground
    O - Body ground
    Back door fully closed and A or B switch turned ON →
    Back door in opening operation →
    Back door fully open
    0 V →
    Alternating between 10 to 14 V and 0 V→
    0 V
    *1 Satellite switch (Back door)
    *2 Transmitter switch (Back door)

    1. *3 When all the conditions listed below are met, the warning buzzer sounds.
      1. Ignition switch is turned ON
      2. Shift lever is moved into any position except P position
      3. Back door is open or power back door system is activated to open
    1. *4 When any condition listed below is met, the warning buzzer turns off.
      1. Shift lever is moved into P position
      2. Back door is fully closed

    HINT:
    Use an oscilloscope to check the output voltages of the power back door main switch, buzzer and pulse sensor.
    If the result is not as specified, the ECU may have a malfunction.