Home › BODY › ENGINE HOOD / DOOR › POWER BACK DOOR SYSTEM

POWER BACK DOOR SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the DATA LIST displayed on the Techstream, you can read the value of the switch, sensor, actuator, etc. without parts removal. Reading the DATA LIST as the first step of troubleshooting is one way to shorten the labor time.

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch ON.

  3. Read the DATA LIST according to the display on the tester.

    Power back door ECU 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Half Latch SW
    Back door lock half-latch switch signal
    / ON or OFF
    ON: Back door is not completely closed
    OFF: Back door is closed
    -
    Full Latch SW
    Back door lock full-latch switch signal
    / ON or OFF
    ON: Back door is open
    OFF: Back door is closed
    -
    Back Door Handle SW
    Back door opener switch signal
    / ON or OFF
    ON: Back door opener switch is pushed
    OFF: Back door opener switch is not pushed
    -
    Door Lock Status
    Back door position switch signal
    / UNLOCK or LOCK
    UNLOCK: Back door is unlocked
    LOCK: Back door is locked
    -
    Door Position
    (Close - 1/4)
    Back door position (Full close - 1/4 open)
    / CAUTION or OK
    CAUTION: Back door position is not fully closed - 1/4 opened
    OK: Back door position is fully closed - 1/4 opened
    *1
    Door Position
    (1/4 - 2/4)
    Back door position (1/4 open - 2/4 open)
    / CAUTION or OK
    CAUTION: Back door position is not 1/4 opened - 2/4 opened
    OK: Back door position is 1/4 opened - 2/4 opened
    *1
    Door Position
    (2/4 - 3/4)
    Back door position (2/4 open - 3/4 open)
    / CAUTION or OK
    CAUTION: Back door position is not 2/4 opened - 3/4 opened
    OK: Back door position is 2/4 opened - 3/4 opened
    *1
    Door Position
    (3/4 - Open)
    Back door position (3/4 open - full open)
    / CAUTION or OK
    CAUTION: Back door position is not 3/4 opened - fully opened
    OK: Back door position is 3/4 opened - fully opened
    *1
    PBD SW Operation
    Power back door switch operation (Satellite switch)
    / 0.8s or ON*2
    0.8s: Satellite switch 0.8sec.-press (long press) operates power back door
    ON*2: Satellite switch 1-press operates power back door
    -
    Buzz Vol PBD Operation
    Warning buzzer volume during power back door operation
    / OFF, SMALL or LARGE
    OFF: Warning buzzer that indicates power back door is operating does not sound
    SMALL: Warning buzzer that indicates power back door is operating sounds at small volume
    LARGE: Warning buzzer that indicates power back door is operation sounds at large volume
    -
    Wirels PBD SW Operation
    Wireless power back door switch operation (Transmitter switch operation)
    / 1TIME, 2TIMES, 0.8sPR or OFF
    1TIME: Transmitter switch 1-press operates power back door
    2TIMES: Transmitter switch 2-presses operates power back door
    0.8sPR: Transmitter switch 0.8s.-press operates power back door
    OFF: Transmitter switch operation is disabled
    -
    PBD Assist Close Operation
    Power back door assist-close operation
    / ON or OFF
    ON: Back door is assist-closing
    OFF: Back door is opened or closed
    -
    PBD Assist Open Operation
    Power back door assist-open operation
    / ON or OFF
    ON: Back door is assist-opening
    OFF: Back door is opened or closed
    -
    PBD Touch Sensor (Right)
    Power back door touch sensor RH signal
    / OFF, ON or OPEN
    OFF: Power back door touch sensor RH is free
    ON: Power back door touch sensor RH is pressed
    OPEN: Power back door touch sensor RH is opened
    -
    PBD Touch Sensor (Left)
    Power back door touch sensor LH signal
    / OFF, ON or OPEN
    OFF: Power back door touch sensor LH is free
    ON: Power back door touch sensor LH is pressed
    OPEN: Power back door touch sensor LH is opened
    -
    PBD Main SW
    Power back door main switch signal
    / ON or OFF
    ON: Orange paint on the top of the switch appears
    OFF: Orange paint on the top of the switch does not appear
    -
    *1 In case that the "CAUTION" is displayed even without applying resistance in each range, there must be a foreign object caught in that range.
    *2 "0.0s" appearing on the display of the Techstream means that a 1-press of the satellite switch operates the power back door.


ACTIVE TEST

HINT:
Performing the ACTIVE TEST using the Techstream allows you to operate the relay, VSV, actuator, etc. without parts removal. Performing the ACTIVE TEST as the first step of troubleshooting is one way to shorten the labor time. It is possible to display the DATA LIST during the ACTIVE TEST.

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch ON.

  3. Perform the ACTIVE TEST according to the display on the tester.

    Back Door ECU 
    Tester Display
    Test Part
    Control Range
    Latch Release
    Back door lock latch is release
    OFF / ON
    -
    PBD Motor
    Power back door motor is operate
    OFF / FORWARD / REVERSE
    Clutch is OFF while power back door motor is operating
    PBD Clutch
    Power back door control clutch is operate
    OFF / ON
    Power back door motor is OFF when clutch is ON
    PBD Buzzer
    Power back door warning buzzer sound
    OFF / ON
    -