Home › BODY › ENGINE HOOD / DOOR › SLIDE DOOR (w/o Power Slide Door)

SLIDE DOOR (w/o Power Slide Door) > REASSEMBLY

for Preparation Click here



1. INSTALL REAR DOOR WIRE SUB-ASSEMBLY LH


    B068588E01
  1. Install the wire.

    NOTICE:
    When installing the wire, push the areas where the clips are installed in order to prevent damage and deformation.

  1. Install the 2 screws.



2. INSTALL REAR DOOR LOCK ASSEMBLY LH


    B067503E01
  1. Apply MP grease to the sliding and rotating areas of the lock.

  1. Apply adhesive to the threads of the screws.

    Adhesive:
    Part No. 08833-00070, THREE BOND 1324 or equivalent

  1. Install the lock to the door panel with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the cable.



3. INSTALL SLIDE DOOR LOCK ASSEMBLY FRONT LH


    B067504E01
  1. Apply MP grease to the sliding and rotating areas of the lock.

  1. Apply adhesive to the threads of the screws.

    Adhesive:
    Part No. 08833-00070, THREE BOND 1324 or equivalent

  1. Install the lock front to the door panel with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the 2 cables.



4. INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH


    B068299E01
  1. Apply MP grease to the sliding and rotating parts of the outside handle frame.

  1. Slide the outside handle frame in the direction indicated by the arrow mark in the illustration.

  1. Using a torx socket wrench (T30), install the outside handle frame with the screw.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

    NOTICE:
    Insert a cover between the nut and the door panel.

  1. Install the open rod.



5. INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY LH


    B066858E01
  1. Install the outside handle pads front and rear.

  1. Pushing the outside handle in the direction indicated by the arrow mark in the illustration, install the outside handle.

    NOTICE:
    If the release plate is not pulled and held when installing the outside handle, it will strike against with the outside handle and become damaged.



6. INSTALL REAR DOOR OUTSIDE HANDLE COVER LH


    B069310E01
  1. Using a torx socket wrench (T30), install the outside handle cover with the screw.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Install the hole plug.



7. INSTALL REAR DOOR STIFFENER CUSHION LH


    B067511
  1. Install the 2 grommets and 2 clips.

  1. Install the stiffener cushion with the clip and 2 screws.



8. INSTALL SLIDE DOOR ATTACHMENT CONTROL LH


    B069443E01
  1. Temporarily install the window frame rear lower with the nut.

  1. Move the window frame rear lower in the direction indicated by the arrow mark in the illustration.



    B068933E01
  1. Apply MP grease to the sliding and rotating areas of the window regulator.

  1. Install the window regulator with the 4 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Install the half stop control lever and door lock control bellcrank.



    B067508E03
  1. Install the power window regulator motor with the 3 screws.

    Torque:
    5.5 N*m{ 58 kgf*cm , 49 in.*lbf }



    B067508E01
  1. Apply MP grease to the sliding and rotating areas of the lock remote control.

  1. Install the lock remote control with the 3 bolts.

    Torque:
    5.5 N*m{ 58 kgf*cm , 49 in.*lbf }



    B067508E02
  1. Apply MP grease to the sliding and rotating areas of the lock actuator.

  1. Install the lock actuator with 2 screws.

    Torque:
    5.5 N*m{ 58 kgf*cm , 49 in.*lbf }



    B067500E01
  1. Install the attachment control with the 8 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    B069312
  1. Install the inside handle with the 2 screws and bolt.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



  1. Install the control cables and the wires.


    B067505E01


    No.
    Cap Color
    Control
    A
    Gray
    Rear Lock Cable
    B
    Black
    Full Open Lock Cable
    C
    -
    Half Open Stopper Cable
    D
    Green
    Front Lock Cable
    E
    Yellow
    Outside Handle Cable



9. INSTALL SLIDE DOOR WINDOW ASSEMBLY LH


    B067494
  1. Open the door glass until the bolts appear in the service holes.

  1. Install the window with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Install the hole plug.



    B067495E02
  1. Put the window frame rear lower in the original position and tighten the nut.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Install the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    B069208
  1. Install the window frame with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Install the glass run.