Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › CONDENSER

CONDENSER > INSTALLATION

for Preparation Click here



1. INSTALL COOLER CONDENSER CORE


    E145272
  1. Install the cooler condenser core with the 2 screws.

    Torque:
    3.9 N*m{ 40 kgf*cm , 35 in.*lbf }

    HINT:
    If the condenser is replaced with a new one, add compressor oil to the new condenser.

    Capacity:
    40 cc (1.4 fl.oz.)

    Compressor oil:
    ND-OIL 8 or equivalent



2. INSTALL NO. 1 RADIATOR SUPPORT


    A162801E01
  1. Install the No. 1 radiator support to the radiator assembly with the 6 bolts.

    Torque:
    Bolt A:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }
    Bolt B:
    3.9 N*m{ 40 kgf*cm , 35 in.*lbf }
    Bolt C:
    6 N*m{ 61 kgf*cm , 4 ft.*lbf }

  1. Attach the clamp.



3. INSTALL RADIATOR SUPPORT CUSHION


    A162805
  1. Install the 2 radiator support cushions to the No. 1 radiator support.



4. CONNECT NO. 2 OIL COOLER OUTLET TUBE SUB-ASSEMBLY


    E146681
  1. Install the No. 2 oil cooler outlet tube sub-assembly with the 2 bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



5. INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY


    A161463
  1. Install the radiator upper support sub-assembly with the 4 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }



6. CONNECT COOLING FAN ECU


    A161472E01
  1. Connect the connector.

  1. Attach the clamp.



7. INSTALL HOOD LOCK SUPPORT SUB-ASSEMBLY


    A161460
  1. Install the hood lock support sub-assembly with the 2 bolts.



    A161458
  1. Attach the clamp.

  1. Connect the low pitched horn and high pitched horn connectors.



    A161459
  1. Connect the ambient temperature sensor connector.



8. INSTALL HOOD LOCK ASSEMBLY


    A162807
  1. Connect the cable to the hood lock assembly.



    A161457
  1. Install the hood lock assembly with the 3 bolts.

    Torque:
    8 N*m{ 82 kgf*cm , 6 ft.*lbf }

  1. With Hood Courtesy Switch:

    1. Connect the connector.



9. INSTALL HOOD LOCK RELEASE LEVER PROTECTOR


    A161456
  1. Engage the 4 claws to install the hood lock release lever protector.



10. INSTALL NO. 1 AIR CLEANER INLET


    A155040
  1. Install the No. 1 air cleaner inlet with the bolt.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



11. INSTALL COOLER REFRIGERANT LIQUID PIPE A
  1. Remove the attached vinyl tape from the pipe and the connecting part of the cooler condenser core.

  1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the pipe joint.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring on the cooler refrigerant liquid pipe A.



    E145271
  1. Install the cooler refrigerant liquid pipe A on the cooler condenser core with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 47 in.*lbf }



12. INSTALL DISCHARGE HOSE SUB-ASSEMBLY
  1. Remove the attached vinyl tape from the tube and the connecting part of the cooler condenser core.

  1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the hose joint.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring on the discharge hose sub-assembly.



    E145270
  1. Install the discharge hose sub-assembly on the cooler condenser core with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 47 in.*lbf }



13. INSTALL FRONT BUMPER ASSEMBLY


    B125282
  1. Push the front bumper onto the front of the vehicle and engage the claws on the left and right sides of the front bumper to install it as shown in the illustration.

    HINT:
    1. Apply protective tape to the bottom part of the front fender to prevent it from being damaged.
    2. Connect the connectors if necessary.



    B125280
  1. Install the 5 clips.



    B125279
  1. Connect the engine under cover to the front bumper assembly with the 8 screws.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62.0 in.*lbf }



    B125278
  1. Connect the fender liner to the front bumper assembly with the 4 screws.



14. INSTALL NO. 2 AIR CLEANER INLET


    A133004
  1. Install the No. 2 air cleaner inlet with the 2 clamps and 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



15. CHARGE WITH REFRIGERANT
  1. Using a vacuum pump, perform a vacuum purging.



  1. Charge refrigerant, HFC-134a (R134a).

    Standard:
    780 +- 30 g (27.5 +- 1.06 oz.)

    SST
    07110-58060   (07117-58060, 07117-58070, 07117-58080, 07117-58090, 07117-78050, 07117-88060, 07117-88070, 07117-88080)


    I030082E10



16. WARM UP ENGINE


17. INSPECT FOR REFRIGERANT LEAK
  1. Using a gas leak detector, check for leakage of the refrigerant.



18. VEHICLE PREPARATION FOR FOG LIGHT AIMING (w/ Fog Light)
  1. Prepare the vehicle:

    1. Ensure there is no damage or deformation to the body around the fog lights.
    2. Fill the fuel tank.
    3. Make sure that the oil is filled to the specified level.
    4. Make sure that the coolant is filled to the specified level.
    5. Inflate the tires to the appropriate pressure.
    6. Place the spare tire, tools, and jack in their original positions.
    7. Unload the trunk.
    8. Sit a person of average weight (68 kg, 150 lb) in the driver's seat.



19. PREPARATION FOR FOG LIGHT AIMING (w/ Fog Light)


    E119934E01
  1. Prepare the vehicle according to the following conditions:

    1. Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the fog lights can be observed and above which it cannot.
    2. Place the vehicle at a 90° angle to the wall.
    3. Create a 7.62 m (25 ft) distance between the vehicle (fog light bulb center) and the wall.
    4. Place the vehicle on a level surface.
    5. Bounce the vehicle up and down to settle the suspension.

      NOTICE:
      A distance of 7.62 m (25 ft) between the vehicle (fog light bulb center) and the wall is necessary for proper aim adjustment. If unavailable, secure a distance of exactly 3 m (9.84 ft) for check and adjustment. (The target zone will change with the distance, so follow the instructions in the illustration.)

  1. Prepare a piece of thick white paper (approximately 2 m (6.6 ft) (height) x 4 m (13.1 ft) (width)) to use as a screen.

  1. Draw a vertical line down the center of screen (V line).



  1. Set the screen as shown in the illustration.


    E119935E01

    HINT:
    1. Stand the screen perpendicular to the ground.
    2. Align the V line on the screen with the center of the vehicle.



    I033423E06
  1. Draw base lines (H line, V LH, V RH lines) on the screen as shown in the illustration.

    HINT:
    Mark the fog light bulb center marks on the screen. If the center mark cannot be observed on the fog light, use the center of the fog light bulb or the manufacturer's name marked on the fog light as the center mark.


    1. H Line (Fog light height):
      Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the fog light bulb center marks of the low-beam fog lights.

    2. V LH Line, V RH Line (Center mark position of left-hand (LH) and right-hand (RH) fog lights):
      Draw two vertical lines so that they intersect the H line at each center mark.



20. FOG LIGHT AIMING INSPECTION (w/ Fog Light)
  1. Cover or disconnect the connector of the fog light on the opposite side to prevent light from the fog light not being inspected from affecting fog light aiming inspection.

  1. Start the engine.

    NOTICE:
    Engine rpm must be 1,500 or more.



  1. Turn on the fog light and make sure that the cutoff line falls within the specified area, as shown in the illustration.


    I041221E08



21. FOG LIGHT AIMING ADJUSTMENT (w/ Fog Light)


    E119936E01
  1. Adjust the fog light aim into the specified range by turning aiming screw with a screwdriver.

    NOTICE:
    The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it and then retighten it, so that the final turn of the screw is in the clockwise direction.