Home › ENGINE › 2GR-FE FUEL › FUEL TANK

FUEL TANK > REMOVAL

for Preparation Click here



1. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)


2. REMOVE CHARCOAL CANISTER PROTECTOR
  1. Remove the 6bolts and the charcoal canister protector.



3. REMOVE REAR FLOOR NO. 2 CROSSMEMBER BRACE LH


A162433
  1. Remove the 2 bolts and the rear floor No. 2 crossmember brace LH.



4. REMOVE FUEL TANK FILLER HOSE COVER


A081606E01
  1. Remove the 3 bolts and the fuel tank filler hose cover.



5. REMOVE FUEL TANK ASSEMBLY


A164973E01
  1. Disconnect the fuel tank vent hose.

    1. Deeply push the connector to release the locking tab.

    2. Pinch portion A.

    3. Pull out the connector.



    A079518E01
  1. Disconnect the fuel tank main tube sub-assembly.

    1. Pinch the tube connector and then pull out the fuel tank main tube sub-assembly.

      NOTICE:
      1. Check if there is any dirt or mud around the connector before this operation and remove the dirt as necessary.
      2. Be careful of mud because the quick connector has an O-ring which seals the pipe and connector that can be contaminated.

      3. A075650E16
        Do not use any tool in this operation.
      4. Do not bend or twist the nylon tube. Protect the connector by covering it with a vinyl or plastic bag.
      5. When the pipe and the connector are stuck, push and pull the connector to release and pull the connector out carefully.



    A079519E01
  1. Disconnect the fuel tank to filler pipe hose.

    1. Loosen the hose clamp bolt and disconnect the fuel tank to filler pipe hose.



    A126852E01
  1. Disconnect the fuel tube.

    1. Pinch the tube connector and then pull out the fuel tank main tube sub-assembly.

      NOTICE:
      1. Check if there is any dirt or mud around the connector before this operation and remove the dirt as necessary.
      2. Be careful of mud because the quick connector has an O-ring which seals the pipe and connector that can be contaminated.
      3. Do not use any tool in this operation.
      4. Do not bend or twist the nylon tube. Protect the connector by covering it with a vinyl or plastic bag.
      5. When the pipe and the connector are stuck, push and pull the connector to release and pull the connector out carefully.



    A079521E01
  1. Remove the 2 wire harness clamps.



    A079522E01
  1. Set up a transmission jack under the fuel tank assembly.

  1. Remove the 6 set bolts of the 3 fuel tank bands.



    A165009E01
  1. While operating the transmission jack, unfasten the 4 claws for the wire harness and disconnect the fuel pump connector, then remove the fuel tank and the 3 fuel tank bands from the vehicle.



6. REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY


A164998E01
  1. Remove the tube joint clip, and pull out the fuel main tube.

    NOTICE:
    1. Check if there is any dirt or mud around the connector before this operation and remove the dirt as necessary
    2. Be careful of mud because the quick connector has an O-ring which seals the pipe and connector that can be contaminated.
    3. Do not use any tool in this operation.
    4. Do not bend or twist the nylon tube. Protect the connector by covering it with a vinyl or plastic bag.
    5. When the pipe and connector are stuck, push and pull the connector to release and pull the connector out carefully.



    A164999
  1. Unfasten the 4 claws and remove the fuel tank main tube from the fuel tank.



7. REMOVE FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE


A165000E01
  1. Using SST, loosen the fuel pump gauge retainer.

    SST
    09808-14020   (09808-01410, 09808-01420, 09808-01430)

    HINT:
    A rib on the fuel pump gauge retainer can be fitted into a tip of SST.

  1. Remove the fuel pump gauge retainer.

  1. Remove the fuel suction tube assembly with pump and gauge and the fuel suction tube set gasket from the fuel tank.

    NOTICE:
    Be careful not bend the arm of the fuel sender gauge.



8. DRAIN FUEL


9. REMOVE FUEL TANK TO FILLER PIPE HOSE


A081607E01
  1. Loosen the hose clamp bolt and remove the fuel tank to filler pipe hose from the fuel tank.



10. REMOVE FUEL TANK VENT HOSE
  1. Remove the hose of the fuel tank vent hose from the 3 hose clamps.



  1. Remove the fuel tank vent hose.

    1. Deeply push the connector to release the locking tab.

    2. Pinch portion A.



    3. Pull out the connector.


      A127073E01