Home › BODY ELECTRICAL › LIGHTING › LIGHTING SYSTEM

LIGHTING SYSTEM > Door Courtesy Switch Circuit

for Preparation Click here


DESCRIPTION

The Multiplex network body ECU detects the condition of the door courtesy switch assembly.

WIRING DIAGRAM


E115590E03


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Body / Data List.

  1. Read the display on the Techstream.

    Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D door Courtesy SW
    Driver side door courtesy switch signal / ON or OFF
    ON: Driver side door open
    OFF: Driver side door closed
    -
    P door Courtesy SW
    Passenger side door courtesy switch signal / ON or OFF
    ON: Passenger side door open
    OFF: Passenger side door closed
    -
    Rear door Courtesy SW
    Rear slide door courtesy switch signal / ON or OFF
    ON: Either right or left rear slide door is open
    OFF: Both the right and left slide doors are closed
    -

    Back Door 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Back Door Courtesy SW
    Back door courtesy switch signal / ON or OFF
    ON: Back door is open
    OFF: Back door is closed
    -



OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
NG


2.INSPECT COURTESY LIGHT SWITCH
  1. Inspect each of the courtesy light switch continuity (Click here for Front, Click here for Rear).



NG
REPLACE COURTESY LIGHT SWITCH
OK


3.INSPECT BACK DOOR LOCK ASSEMBLY
  1. Inspect the courtesy light switch terminal of the back door lock assembly (Click here).



NG
REPLACE BACK DOOR LOCK ASSEMBLY
OK


4.CHECK HARNESS AND CONNECTOR


  1. Disconnect the 1P, B7 and B9 connector from the instrument panel junction block assembly.


    E067348E07



  1. Check the resistance between each of the terminals of instrument panel junction block assembly connector side and body ground as shown in the chart below.


    E067349E09


    Resistance:

    Inspect area
    Tester Connection
    Specified Condition
    Front driver door open → close
    B9-14 - Body ground
    Below 1 Ω → 10 kΩ or higher
    Front passenger door open → close
    B7-23 - Body ground
    Below 1 Ω → 10 kΩ or higher
    Rear RH slide door open → close
    B9-16 - Body ground
    Below 1 Ω → 10 kΩ or higher
    Rear LH slide door open → close
    1P-19 - Body ground
    Below 1 Ω → 10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (BACK DOOR COURTESY LIGHT SWITCH CIRCUIT)


  1. Measure voltage between the terminal B7-25 of the multiplex network body ECU and body ground.


    E067349E10

    Voltage:
    Tester Connection
    Condition
    Specified Condition
    B7-25 - Body ground
    Back door is open
    Below 1 V
    B7-25 - Body ground
    Back door is closed
    10 to 14 V



OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
NG


6.CONFIRM VEHICLE TYPE
  1. Check the vehicle models.
    A: w/o Power back door
    B: w/ Power back door



A
REPAIR OR REPLACE HARNESS OR CONNECTOR
B


7.INSPECT POWER BACK DOOR SYSTEM
  1. Inspect the power back door circuit (Click here).



NG
CHECK AND REPLACE POWER BACK DOOR SYSTEM
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR