Home › BODY ELECTRICAL › LIGHTING › LIGHTING SYSTEM

LIGHTING SYSTEM > DRL Relay Circuit

for Preparation Click here


DESCRIPTION

The Multiplex network body ECU controls the DRL No.2 relay.

WIRING DIAGRAM


E115588E04


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Body / Active Test.

  1. Check the operation.

    Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Relay of DRL
    Relay of DRL (Ignition SW is ON, engine is stopped and light control SW is in OFF position).
    ON/OFF
    -



OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
NG


2.INSPECT DRL NO.2 RELAY


    B016200
  1. Inspect DRL No.2 Relay continuity.

    Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Always
    10 kΩ or higher
    3 - 5
    Apply B+ between the terminal 1 and 2
    Below 1 Ω



NG
REPLACE DRL NO.2 RELAY
OK


3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)


    E124416E01
  1. Disconnect the connector from the instrument panel junction block assembly.

  1. Measure the voltage according to the value(s) in the table below.

    Voltage:
    Tester Connection
    Condition
    Specified Condition
    1C-23 - Body ground
    Always
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


  1. Reconnect the connector to the instrument panel junction block assembly.


    E067348E04

  1. Measure the voltage according to the value(s) in the table below.

    Voltage:
    Tester Connection
    Condition
    Specified Condition
    1C-23 - Body ground
    Ignition switch: OFF
    10 to 14 V
    1C-23 - Body ground
    Ignition switch: ON
    Below 1 V



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
OK


5.INSPECT RELAY (DRL NO.3, DRL NO.4)


    B016200
  1. Inspect DRL NO.4 Relay continuity.

    Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Always
    10 kΩ or higher
    3 - 5
    Apply B+ between the terminal 1 and 2
    Below 1 Ω



    E068810
  1. Inspect DRL NO.3 Relay continuity.

    Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 4
    Always
    Below 1 Ω
    3 - 4
    Apply B+ between the terminal 1 and 2
    10 kΩ or higher
    3 - 5
    Always
    10 kΩ or higher
    3 - 5
    Apply B+ between the terminal 1 and 2
    Below 1 Ω



NG
REPLACE RELAY
OK


6.INSPECT DAYTIME RUNNING LIGHT RESISTER


    E124415E01
  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    0.94 to 1.04 Ω



NG
REPLACE DAYTIME RUNNING LIGHT RESISTER
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR