Home › ENGINE › 2GR-FE EXHAUST › EXHAUST PIPE (for 2WD)

EXHAUST PIPE (for 2WD) > INSTALLATION

for Preparation Click here



1. INSTALL HEATED OXYGEN SENSOR (for Bank 2 Sensor 2)


    A163271E01
  1. Using SST, install the heated oxygen sensor to the front exhaust pipe.

    SST
    09224-00010  

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf } for use with SST
    44 N*m{ 449 kgf*cm , 32 ft.*lbf } for use without SST

    HINT:
    1. Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
    2. Make sure that SST and a wrench are connected in a straight line.



2. INSTALL FRONT EXHAUST PIPE ASSEMBLY
  1. Install 2 new gaskets to the front exhaust pipe assembly.



  1. Install the front exhaust pipe assembly with the 4 nuts.

    Torque:
    62 N*m{ 632 kgf*cm , 46 ft.*lbf }



    A162908



3. INSTALL CENTER EXHAUST PIPE ASSEMBLY


    A160224
  1. Using a vernier caliper, measure the free length of the compression spring.

    Minimum length:
    38.86 mm (1.5299 in.)

    If the length is less than the minimum, replace the compression spring.



    A133205E01
  1. Install a new gasket by hand so that its surface is flush with the front exhaust pipe assembly.

    NOTICE:
    1. Make sure the gasket is facing the correct direction.
    2. Do not reuse the old gasket.
    3. Do not push in the gasket while installing the center exhaust pipe assembly.

  1. Connect the 2 exhaust pipe supports, and install the center exhaust pipe assembly.



  1. Install the 2 compression springs and 2 bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



    A162482

  1. Connect the heated oxygen sensor (for bank 2 sensor 2) connector.



4. INSTALL NO. 1 EXHAUST PIPE SUPPORT BRACKET
  1. Install the No. 1 exhaust pipe support bracket to oil pan sub-assembly with 2 new nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Loosen the No. 1 exhaust pipe support bracket bolts.

  1. Install the clamp to No. 1 exhaust pipe support bracket.

  1. Retighten the No. 1 exhaust pipe support bracket bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



  1. Install the clamp with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



    A162909



5. INSTALL TAIL EXHAUST PIPE ASSEMBLY
  1. Install a new gasket to the center exhaust pipe assembly.

  1. Connect the 3 exhaust pipe supports, and install the tail exhaust pipe assembly.



  1. Install 2 new bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



    A162481



6. INSTALL HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)


    A162954E01
  1. Using SST, install the heated oxygen sensor.

    SST
    09224-00010  

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf } for use with SST
    44 N*m{ 449 kgf*cm , 32 ft.*lbf } for use without SST

    HINT:
    1. Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
    2. Make sure that SST and a wrench are connected in a straight line.

  1. Connect the heated oxygen sensor (for Bank 1 Sensor 2) connector.



7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


8. INSPECT FOR EXHAUST GAS LEAK
If exhaust gas is leaking, repair the leak. Replace damaged parts as necessary.