Home › ENGINE › 2GR-FE EXHAUST › EXHAUST PIPE (for 4WD)

EXHAUST PIPE (for 4WD) > INSTALLATION

for Preparation Click here



1. INSTALL HEATED OXYGEN SENSOR (for Bank 2 Sensor 2)


    A163271E01
  1. Using SST, install the heated oxygen sensor to the front exhaust pipe.

    SST
    09224-00010  

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf } for use with SST
    44 N*m{ 449 kgf*cm , 32 ft.*lbf } for use without SST

    HINT:
    1. Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
    2. Make sure that SST and a wrench are connected in a straight line.



2. INSTALL FRONT EXHAUST PIPE ASSEMBLY
  1. Install a new gasket to the front exhaust pipe assembly.



  1. Install the front exhaust pipe assembly with the 2 nuts.

    Torque:
    62 N*m{ 632 kgf*cm , 46 ft.*lbf }



    A162667



3. INSTALL CENTER EXHAUST PIPE ASSEMBLY
  1. Install 2 new gaskets to the center exhaust pipe assembly.

  1. Connect the 2 exhaust pipe supports, and install the center exhaust pipe assembly.



  1. Install 2 new bolts and 2 nuts.

    Torque:
    Bolt:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }
    Nut:
    62 N*m{ 632 kgf*cm , 46 ft.*lbf }



    A162162



4. INSTALL NO. 1 EXHAUST PIPE SUPPORT BRACKET
  1. Install the No. 1 exhaust pipe support bracket to oil pan sub-assembly with 2 new nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Loosen the No. 1 exhaust pipe support bracket bolts.

  1. Install the clamp to No. 1 exhaust pipe support bracket.

  1. Retighten the No. 1 exhaust pipe support bracket bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



  1. Install the clamp with a new bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



    A162668

  1. Connect the heated oxygen sensor (for bank 2 sensor 2) connector.



5. INSTALL TAIL EXHAUST PIPE ASSEMBLY
  1. Install a new gasket to the center exhaust pipe assembly.

  1. Connect the 4 exhaust pipe supports, and install the tail exhaust pipe assembly.



  1. Install 2 new bolts.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



    A162161



6. INSTALL HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)


    A163385E01
  1. Using SST, install the heated oxygen sensor.

    SST
    09224-00010  

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf } for use with SST
    44 N*m{ 449 kgf*cm , 32 ft.*lbf } for use without SST

  1. Connect the heated oxygen sensor (for Bank 1 Sensor 2) connector.

    HINT:
    1. Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
    2. Make sure that SST and a wrench are connected in a straight line.



7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


8. INSPECT FOR EXHAUST GAS LEAK
If exhaust gas is leaking, repair the leak. Replace damaged parts as necessary.