Home › CRUISE CONTROL SYSTEM › CRUISE CONTROL › DYNAMIC LASER CRUISE CONTROL SYSTEM

DYNAMIC LASER CRUISE CONTROL SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



READ DATA LIST

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the Techstream on.

  4. Enter the following menus: Powertrain / Laser Cruise / Data List.

  5. Read the Data List according to the display on the Techstream.

    ECM (Laser Cruise): 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Accel Request
    Accelerator request signal / min.: -2621.44 k/h/s, max.: 2621.36 k/h/s
    Actual demanded acceleration request
    -
    Vehicle Distance
    Laser sensor / min.: 0 m (0 ft.), max.: 255 m (836.65 ft.)
    Distance to vehicle in front
    -
    L/C Option Flag
    Dynamic laser cruise option flag / No or Yes
    Yes: Dynamic laser cruise control system can be used
    No: Dynamic laser cruise control system cannot be used
    -
    Car Dist Time Setting
    Vehicle distance time setting condition / Shrt, Mid, Long, No
    Vehicle-to-vehicle distance selected by steering pad switch (distance control switch)
    -
    O/D Cut Request
    O/D cut request / Not Req or Request
    Not Req: Idling
    -
    Shift Down Rqst to 3rd
    Shift down request to 3rd gear / Not Req or Request
    Not Req: Idling
    -
    Shift Down Rqst to 4th
    Shift down request to 4th gear / Not Req or Request
    Not Req: Idling
    -
    Shift Down Rqst to 5th
    Shift down request to 5th gear / Not Req or Request
    Not Req: Idling
    -
    Alarm Request
    Alarm request signal / Not Req or Request
    Request: When beeping
    Not Req: When not beeping
    -
    All Throttle Close Rqst
    All throttle close request / Not Req or Request
    ON: Request
    OFF: Not Req
    -
    Brake Control Request
    Brake control request / Not Req or Request
    ON: Request
    OFF: Not Req
    -
    Targ Decl Slope
    Cruise target deceleration slope / 0.03, 0.06, 0.11, 0.15
    0.03, 0.06, 0.11, 0.15
    -
    CCS Vehicle Spd
    Vehicle speed sensor / min.: 0 km/h (0 mph), max.: 255 km/h (158 mph)
    Actual vehicle speed
    -
    CCS Mem Vehicle Spd
    Cruise control memorized speed / min.: 0 km/h (0 mph), max.: 200 km/h (125 mph)
    Memorized speed: Cruise control activated
    -
    Throttle Opening Angle
    Throttle opening angle / min.: 0°, max.: 125°
    Actual demanded throttle angle
    -
    Cruise Control
    Cruise control system active condition / ON or OFF
    ON: Cruise control activated
    OFF: Cruise control deactivated
    -
    Main SW M-CPU
    Main switch signal (Main CPU) / ON or OFF
    ON: Main switch on
    OFF: Main switch off
    3
    CCS Ready M-CPU
    Cruise control system standby condition (Main CPU) / ON or OFF
    Each time main switch is pushed, ON/OFF changes
    1
    CCS Indicator M-CPU
    Cruise indicator signal (Main CPU) / ON or OFF
    ON: "CRUISE" on
    OFF: "CRUISE" off
    2
    Cancel Switch
    CANCEL switch signal / ON or OFF
    ON: CANCEL switch on
    OFF: CANCEL switch off
    -
    SET/COAST Switch
    SET/COAST switch signal / ON or OFF
    ON: - (COAST)/SET switch on
    OFF: - (COAST)/SET switch off
    -
    RES/ACC Switch
    RES/ACC switch signal / ON or OFF
    ON: + (ACCEL)/RES (RESUME) switch on
    OFF: + (ACCEL)/RES (RESUME) switch off
    -
    Stp Light SW M-CPU
    Stop light switch signal (Main CPU) / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -
    Cruise Operation Status
    Transmission range sensor signal / ON or OFF
    ON: Shift lever in D or 4 position
    OFF: Shift lever in any position except in D or 4 position
    -
    VSC Fail Safe Flag
    VSC fail-safe flag / ON or OFF
    VSC communication fail safe in operation
    -
    # Codes
    Number of DTC recorded / 0 to 255
    Number of DTCs will be displayed
    -

    HINT:
    1. 3 is OK, but 1 is NG → ECM failure
    2. 1 is OK, but 2 is NG → DTC output or ECM failure
    3. 3 is OK, but cruise indicator does not turn on → Indicator, wire harness, or ECM failure


ACTIVE TEST

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the Techstream on.

  4. Enter the following menus: All ECUs / (desired system) / Active Test.

  5. Perform "Active Test" according to the display on the Techstream.

    HINT:
    The ignition switch must be turned on to proceed with the Active Test using the Techstream.


    ABS/VSC/TRAC: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Buzzer
    Skid control buzzer
    ON / OFF
    Buzzer can be heard

    Combination Meter: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Indicat. Lamp Cruise
    "CRUISE" indicator light
    BLINK / OFF
    -
    Indicat. Laser Cruise Display
    Multi-information display
    ON / OFF
    -
    Indicat. Lamp L-Cruise Check
    Master warning light
    ON / OFF
    -
    Indicat. Lamp L-Cruise Ready
    "READY" indicator light
    ON / OFF
    -