Home › SUSPENSION & AXLE › SUSPENSION › REAR COIL SPRING

REAR COIL SPRING > REMOVAL

for Preparation Click here



1. REMOVE REAR WHEEL


2. REMOVE SKID CONTROL SENSOR WIRE (for 2WD)


    G023899
  1. Disconnect the skid control sensor connector.

  1. Remove the bolt and disconnect the bracket from the rear axle beam assembly.

    HINT:
    Separate the RH side by the same procedures as the LH side.



3. SEPARATE SPEED SENSOR REAR LH (for 4WD)


    G023898
  1. Remove the bolt and speed sensor rear LH.



4. SEPARATE SPEED SENSOR REAR RH (for 4WD)

HINT:
Separate the RH side by the same procedures as the LH side.



5. REMOVE EXHAUST PIPE ASSEMBLY TAIL

HINT:
  1. 2WD DRIVE TYPE
  2. 4WD DRIVE TYPE



6. REMOVE PROPELLER W/CENTER BEARING SHAFT ASSEMBLY (for 4WD)

HINT:
(Click here)



7. SEPARATE REAR DRIVE SHAFT ASSEMBLY LH (for 4WD)


    G023905E01
  1. Place matchmarks on the rear drive shaft assembly LH and differential flange.

  1. Remove the 4 nuts and 4 washers, separate rear drive shaft assembly LH.



8. SEPARATE REAR DRIVE SHAFT ASSEMBLY RH (for 4WD)

HINT:
Separate the RH side by the same procedures as the LH side.



9. REMOVE DIFFERENTIAL CARRIER ASSEMBLY REAR (for 4WD)

HINT:
(Click here)



10. SEPARATE PARKING BRAKE CABLE ASSEMBLY NO.3


    G023904
  1. Remove the 2 bolts and parking brake cable assembly No.3.



11. SEPARATE PARKING BRAKE CABLE ASSEMBLY NO.2

HINT:
Separate the RH side by the same procedures as the LH side.



12. SEPARATE REAR BRAKE TUBE NO.2


    G025779E01
  1. Using SST, separate the brake tube from the flexible hose. Catch the brake fluid with a container as it drains out.

    SST
    09023-00101  



    G025780
  1. Remove the clip, and separate the flexible hose.



    C088688
  1. Remove the bolt and separate the brake tube from rear axle beam assembly.



13. SEPARATE REAR BRAKE TUBE NO.1
SST
09023-00101  

HINT:
Separate the RH side by the same procedures as the LH side.



14. REMOVE FUEL TANK FILLER HOSE COVER
  1. Remove the 2 bolts, 3 screws, 3 nuts and fuel tank filler pipe protector.

  1. Remove the 3 bolts and fuel tank filler hose cover.



15. REMOVE REAR FLOOR NO.2 CROSSMEMBER BRACE LH
  1. Remove the 2 bolts and floor No.2 crossmember brace.



16. REMOVE REAR FLOOR NO.2 CROSSMEMBER BRACE RH

HINT:
Remove the RH side by the same procedures as the LH side.



17. LOOSEN REAR AXLE BEAM ASSEMBLY


    G025783
  1. Refer to hint below.

    HINT:
    Loosen the RH side by the same procedures as the LH side.

    NOTICE:
    1. When loosening the bolt, hold the nut not to rotate.
    2. Do not remove the bolt and nut.



18. SEPARATE SHOCK ABSORBER ASSEMBLY REAR LH


    C088670
  1. Support the rear axle beam assembly with a jack.



    C088671
  1. Remove the bolt and separate the shock absorber assembly rear LH.



19. SEPARATE SHOCK ABSORBER ASSEMBLY REAR RH

HINT:
Separate the RH side by the same procedures as the LH side.



20. REMOVE COIL SPRING REAR LH


    C088693
  1. Apply a shop rug between the coil spring rear LH and rear axle beam assembly.



    C088694
  1. Apply a shop rug between the coil spring rear RH and rear axle beam assembly.

  1. Remove the coil spring LH by slowly lowering the jack.



21. REMOVE REAR COIL SPRING INSULATOR UPPER LH


    G024682
  1. Remove the rear coil spring insulator upper LH from the coil spring rear LH.