Home › SUSPENSION & AXLE › SUSPENSION › REAR AXLE BEAM

REAR AXLE BEAM > REMOVAL

for Preparation Click here



1. REMOVE REAR WHEEL


2. REMOVE SKID CONTROL SENSOR WIRE (for 2WD)

HINT:
(Click here)

HINT:
Disconnect the RH side by the same procedures as the LH side.



3. SEPARATE SPEED SENSOR REAR LH (for 4WD)

HINT:
(Click here)



4. SEPARATE SPEED SENSOR REAR RH (for 4WD)

HINT:
Separate the RH side by the same procedures as the LH side.



5. REMOVE EXHAUST PIPE ASSEMBLY TAIL

HINT:
  1. 2WD DRIVE TYPE
  2. 4WD DRIVE TYPE



6. REMOVE PROPELLER W/CENTER BEARING SHAFT ASSEMBLY (for 4WD)

HINT:
(Click here)



7. REMOVE REAR AXLE SHAFT LH NUT (for 4WD)

HINT:
(Click here)



8. REMOVE REAR AXLE SHAFT RH NUT (for 4WD)

HINT:
Remove the RH side by the same procedures as the LH side.



9. REMOVE REAR DRIVE SHAFT ASSEMBLY LH (for 4WD)

HINT:
(Click here)



10. REMOVE REAR DRIVE SHAFT ASSEMBLY RH (for 4WD)

HINT:
Remove the RH side by the same procedures as the LH side.



11. REMOVE DIFFERENTIAL CARRIER ASSEMBLY REAR (for 4WD)

HINT:
(Click here)



12. SEPARATE PARKING BRAKE CABLE ASSEMBLY NO.3

HINT:
(Click here)



13. SEPARATE PARKING BRAKE CABLE ASSEMBLY NO.2

HINT:
Separate the RH side by the same procedures as the LH side.



14. SEPARATE REAR BRAKE TUBE NO.2

HINT:
(Click here)

SST
09023-00101  


15. SEPARATE REAR BRAKE TUBE NO.1
SST
09023-00101  

HINT:
Separate the RH side by the same procedures as the LH side.



16. REMOVE FUEL TANK FILLER HOSE COVER

HINT:
(Click here)



17. REMOVE REAR FLOOR NO.2 CROSSMEMBER BRACE LH

HINT:
(Click here)



18. REMOVE REAR FLOOR NO.2 CROSSMEMBER BRACE RH

HINT:
Remove the RH side by the same procedures as the LH side.



19. LOOSEN REAR AXLE BEAM ASSEMBLY

HINT:
(Click here)



20. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY LH (for DISC REAR BRAKE)
  1. Remove the 2 bolts and separate the rear disc brake caliper assembly LH.



21. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY RH (for DISC REAR BRAKE)

HINT:
Separate the RH side by the same procedures as the LH side.



22. REMOVE REAR DISC (for DISC REAR BRAKE)


23. REMOVE REAR BRAKE DRUM SUB-ASSEMBLY (for DRUM REAR BRAKE)


24. REMOVE REAR AXLE HUB & BEARING ASSEMBLY LH (for 2WD)

HINT:
(Click here)



25. REMOVE REAR AXLE HUB & BEARING ASSEMBLY RH (for 2WD)

HINT:
Remove the RH side by the same procedures as the LH side.



26. REMOVE REAR AXLE HUB & BEARING ASSEMBLY LH (for 4WD)

HINT:
(Click here)



27. REMOVE REAR AXLE HUB & BEARING ASSEMBLY RH (for 4WD)

HINT:
Remove the RH side by the same procedures as the LH side.



28. REMOVE PARKING BRAKE PLATE SUB-ASSEMBLY LH (for DISC REAR BRAKE)
  1. 2WD DRIVE TYPE: Remove the rear axle bearing retainer inner LH and parking brake plate sub-assembly LH.

  1. 4WD DRIVE TYPE: Remove the rear axle bearing retainer outer and parking brake plate sub-assembly LH.



29. REMOVE PARKING BRAKE PLATE SUB-ASSEMBLY RH (for DISC REAR BRAKE)

HINT:
Remove the RH side by the same procedures as the LH side.



30. REMOVE BRAKE BACKING PLATE SUB-ASSEMBLY LH (DRUM REAR BRAKE)
  1. Remove the 2 rear axle bearing retainer inner LH and parking brake plate sub-assembly LH.



31. REMOVE BRAKE BACKING PLATE SUB-ASSEMBLY RH (for DRUM REAR BRAKE)

HINT:
Remove the RH side by the same procedures as the LH side.



32. SEPARATE SHOCK ABSORBER ASSEMBLY REAR LH

HINT:
(Click here)



33. SEPARATE SHOCK ABSORBER ASSEMBLY REAR RH

HINT:
Separate the RH side by the same procedures as the LH side.



34. REMOVE COIL SPRING REAR LH

HINT:
(Click here)



35. REMOVE COIL SPRING REAR RH

HINT:
Remove the RH side by the same procedures as the LH side.



36. REMOVE REAR AXLE BEAM ASSEMBLY


    G025783
  1. Support the rear axle beam assembly with a jack.

  1. Remove the 2 bolts and 2 nuts.

  1. Remove the rear axle beam assembly.

    NOTICE:
    When loosening the bolt, hold the nut not to rotate.



37. REMOVE REAR BRAKE TUBE FLEXIBLE HOSE


    G025786E01
  1. Using SST, separate the brake tube from the flexible hose.

    SST
    09023-00101  

  1. Remove the clip and flexible hose.

    HINT:
    Remove the RH side by the same procedures as the LH side.



38. REMOVE REAR AXLE CARRIER BUSH LH


    G025784E01
  1. Place matchmarks on the 2 notches of the bushing and rear axle beam assembly.

  1. Using a chisel and hammer, bend the 2 portions of the bushing rib.

    HINT:
    Bend the bushing rib until the claw of SST can be hung.

  1. Using SST, remove the bushing from the rear axle beam assembly.

    SST
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04020, 09955-04051, 09957-04010, 09958-04011)
    09950-60010   (09951-00630)

    NOTICE:
    If there is a scratch on the axle beam, paint it.



39. REMOVE REAR AXLE CARRIER BUSH RH
SST
09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04020, 09955-04051, 09957-04010, 09958-04011)
09950-60010   (09951-00630)

HINT:
Remove the RH side by the same procedures as the LH side.



40. REMOVE REAR AXLE BEAM DAMPER
  1. Remove the rear axle beam damper from the rear axle beam assembly.