Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › AIRBAG SYSTEM

DTC    B1635/87    Short in Rear Curtain Shield Squib LH Circuit

for Preparation Click here


DESCRIPTION

The rear curtain shield squib LH circuit consists of the center airbag sensor assembly and the curtain shield airbag assembly LH.
The circuit instructs the SRS to deploy when deployment conditions are met.
DTC B1635/87 is recorded when a short circuit is detected in the rear curtain shield squib LH circuit.

DTC No.
DTC Detecting Condition
Trouble Area
B1635/87
  1. Short circuit between CL2+ wire harness and CL2- wire harness of rear curtain shield squib LH
  2. Rear curtain shield squib LH malfunction
  3. Center airbag sensor assembly malfunction
  1. Curtain shield airbag assembly LH (Rear curtain shield squib LH)
  2. Center airbag sensor assembly
  3. Floor wire

WIRING DIAGRAM


C128524E35


INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting the "check mode" (signal check) with the Techstream (Click here).
  2. After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).

1.CHECK CURTAIN SHIELD AIRBAG ASSEMBLY LH (REAR CURTAIN SHIELD SQUIB LH)


    C111681E04
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect the connectors from the curtain shield airbag assembly LH.

  1. Connect SST (resistance 2.1 Ω) to the floor wire.

    CAUTION:
    Never connect a tester to the curtain shield airbag assembly LH (rear curtain shield squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting.
    Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1635/87 is not output.

    HINT:
    Codes other than DTC B1635/87 may be output at this time, but they are not related to this check.



NG
Go to step 2
OK

REPLACE CURTAIN SHIELD AIRBAG ASSEMBLY LH 

2.CHECK CONNECTORS
  1. Turn the ignition switch to the LOCK position.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect SST (resistance 2.1 Ω) from the floor wire.

  1. Check that the floor wire connectors (on the curtain shield airbag assembly LH side) are not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



NG
REPAIR OR REPLACE FLOOR WIRE
OK


3.CHECK FLOOR WIRE (REAR CURTAIN SHIELD SQUIB LH CIRCUIT)


    C111682E24
  1. Disconnect the connector from the center airbag sensor assembly.

  1. Release the activation prevention mechanism built into connector "B" (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Resistance:
    Tester connection
    Condition
    Specified condition
    C16-1 (CL2+) -
    Body ground
    Always
    1 MΩ or higher
    C16-2 (CL2-) -
    Body ground
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE FLOOR WIRE
OK


4.CHECK CENTER AIRBAG SENSOR ASSEMBLY


    C111683E02
  1. Connect the connectors to the curtain shield airbag assembly LH and the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch to the LOCK position.

  1. Turn the ignition switch to the ON position, and wait for at least 60 seconds.

  1. Check the DTCs (Click here).

    OK:
    DTC B1635/87 is not output.

    HINT:
    Codes other than DTC B1635/87 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY
OK

USE SIMULATION METHOD TO CHECK