Home › BODY › ENGINE HOOD / DOOR › POWER BACK DOOR

POWER BACK DOOR > DISASSEMBLY

for Preparation Click here


HINT:
When the battery is reconnected, the back door is locked and cannot be opened. Therefore, it is necessary to unlock the back door using the door control switch or transmitter switch.



1. REMOVE BACK DOOR SCUFF PLATE


    B067743
  1. Using a clip remover, disengage the 5 clips to remove the back door center garnish.



2. REMOVE QUARTER TRIM PANEL ASSEMBLY FRONT LH


3. REMOVE RR WINDOW SIDE GARNISH ASSEMBLY NO.2 LH


4. REMOVE POWER BACK DOOR ROD


    B067791
  1. Remove the 2 clips and rod.



5. REMOVE POWER BACK DOOR DRIVE UNIT


    B067785
  1. Remove the 3 bolts and drive unit.



6. REMOVE BACK DOOR GARNISH CENTER


    B067782E01
  1. Using a clip remover, disengage the 5 clips and remove the garnish.



7. REMOVE BACK DOOR SIDE GARNISH LH
  1. Using a clip remover, disengage the 3 clips and remove the side garnish.



8. REMOVE BACK DOOR SIDE GARNISH RH
  1. Using a clip remover, disengage the 3 clips and remove the side garnish.



9. REMOVE BACK DOOR STAY BRACKET UPPER LH
  1. Remove the 2 bolts and bracket.



10. REMOVE BACK DOOR PULL STRAP


    B067784E01
  1. Using a screwdriver, disengage the 3 claws and remove the strap cover.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the bolt and strap.



11. REMOVE BACK DOOR TRIM BOARD ASSEMBLY


    B067783E01
  1. Using a screwdriver, disengage the 14 clips and remove the trim board.

    HINT:
    Tape the screwdriver tip before use.



12. REMOVE POWER BACK DOOR TOUCH SENSOR LH


    B067786
  1. Remove the 4 screws.

  1. Using a clip remover, remove the clip and touch sensor.



13. REMOVE POWER BACK DOOR TOUCH SENSOR RH
  1. Remove the 4 screws.

  1. Using a clip remover, remove the clip and touch sensor.



14. REMOVE BACK-UP LIGHT ASSEMBLY LH


    I035545E03
  1. Disconnect the connector.

  1. Release the 2 claw fittings and remove the 4 nuts and the back-up light assembly.



15. REMOVE BACK-UP LIGHT ASSEMBLY RH


    I035545E03
  1. Disconnect the connector.

  1. Release the 2 claw fittings and remove the 4 nuts and the back-up light assembly.



16. REMOVE BACK DOOR GARNISH SUB-ASSEMBLY OUTSIDE


17. REMOVE BACK DOOR WITH MOTOR LOCK ASSEMBLY


    B069066
  1. Disconnect the connector.

  1. Remove the 4 bolts and lock.



18. REMOVE BACK DOOR BASE STOPPER BRACKET
  1. Remove the 2 bolts and bracket.



19. REMOVE BACK DOOR STOPPER LOWER
  1. Remove the 2 bolts and stopper.



20. REMOVE REAR SPOILER COVER


    B067744
  1. Install the rear spoiler with the 3 nuts and 2 clips.

  1. Connect the center stop light connector.



21. REMOVE BACK DOOR STAY SUB-ASSEMBLY LH
  1. Install the stay with the bolts to the door panel.

    Torque:
    19.5 N*m{ 200 kgf*cm , 14 ft.*lbf } for door side

  1. Install the stay with the 2 bolts to the body panel.

    Torque:
    17.5 N*m{ 180 kgf*cm , 13 ft.*lbf } for body side



22. REMOVE BACK DOOR STAY SUB-ASSEMBLY RH