Home › BODY › ENGINE HOOD / DOOR › POWER SLIDE DOOR SYSTEM

POWER SLIDE DOOR SYSTEM > Power Slide Door LH does not Operate When Using Inside / Outside Handle

for Preparation Click here


DESCRIPTION

  1. The inside / outside handles have the ability to control operation of the power slide door. Pulling either handle transmits a request signal to the power slide door ECU LH, which then commands the power slide door control motor and clutch to open / close the power slide door.
  2. The slide door lock remote control assembly has the handle operation detect switch for detection of switch operation and also the child protection detect switch for the child lock function that disables the power slide door control switch LH function while the child lock is ON.
  3. If there is a malfunction detected in these 2 detection switches or the wire harness, replace the slide door lock remote control assembly LH.

WIRING DIAGRAM

Click here.

INSPECTION PROCEDURE

1.OPERATION CHECK
  1. If the power slide door does not operate when trying to open it, proceed to A.

  1. If the power slide door does not operate when trying to close it, proceed to B.



B
Go to step 3
A


2.CHECK SLIDE DOOR CLOSER SYSTEM
  1. Check if the slide door closer system operates.



NG
GO TO SLIDE DOOR CLOSER SYSTEM
OK


3.READ VALUE USING TECHSTREAM
  1. Using the Techstream, check the DATA LIST for proper functioning of the handle operation detect switch.

    OK (Power slide door ECU LH): 
    Item
    Measurement Item / Display (Range)
    Normal Condition
    Diagnostic Note
    Handle Switch
    Handle operation detect switch signal
    / ON or OFF
    ON: Slide door inside / outside handle is pulled
    OFF: Slide door inside / outside handle is not pulled
    -



OK
Go to step 6
NG


4.INSPECT SLIDE DOOR LOCK REMOTE CONTROL SUB-ASSEMBLY LH (HANDLE OPERATION DETECT SWITCH)


    B068910E02
  1. Inspect the resistance of the switch.

    Resistance:
    Terminal No.
    Lever Position
    Specified Condition
    1 - 3
    Unlock
    10 kΩ or higher
    Lock
    Below 1 Ω



NG
REPLACE SLIDE DOOR LOCK REMOTE CONTROL SUB-ASSEMBLY LH
OK


5.CHECK WIRE HARNESS (SLIDE DOOR LOCK REMOTE CONTROL - POWER SLIDE DOOR ECU LH)


    B068450E01
  1. Disconnect the S20 remote control and P25 ECU connectors.

  1. Check the resistance between the wire harness side connectors.

    Resistance (Check for open circuit):
    Terminal No.
    Specified Condition
    S20-1 - P25-3 (HSW)
    Below 1 Ω

  1. Check the resistance between the S20 remote control connector and body ground.

    Resistance (Check for open circuit):
    Terminal No.
    Specified Condition
    S20-3 - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE POWER SLIDE DOOR ECU LH 

6.READ VALUE USING TECHSTREAM
  1. Using the Techstream, check the DATA LIST for proper functioning of the child protection detect switch.

    OK (Power slide door ECU LH): 
    Item
    Measurement Item / Display (Range)
    Normal Condition
    Diagnostic Note
    Child Lock Switch
    Child protection detect switch signal
    / ON or OFF
    ON: Child lock lever is LOCK
    OFF: Child lock lever is UNLOCK
    -



OK
REPLACE POWER SLIDE DOOR ECU LH
NG


7.INSPECT SLIDE DOOR LOCK REMOTE CONTROL SUB-ASSEMBLY LH (CHILD PROTECTION DETECT SWITCH)


    B068911E01
  1. Inspect the resistance of the switch.

    Resistance:
    Terminal No.
    Lever Position
    Specified Condition
    4 - 5
    Unlock
    10 kΩ or higher
    Lock
    Below 1 Ω



NG
REPLACE SLIDE DOOR LOCK REMOTE CONTROL SUB-ASSEMBLY LH
OK


8.CHECK WIRE HARNESS (SLIDE DOOR LOCK REMOTE CONTROL - POWER SLIDE DOOR ECU LH)


    B068450E01
  1. Disconnect the S20 switch and P25 ECU connectors.

  1. Check the resistance between the wire harness side connectors.

    Resistance (Check for open circuit):
    Terminal No.
    Specified Condition
    S20-5 - P25-18 (CPSW)
    Below 1 Ω

  1. Check the resistance between the S20 switch connector and body ground.

    Resistance (Check for open circuit):
    Terminal No.
    Specified Condition
    S20-4 - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE POWER SLIDE DOOR ECU LH