Home › BODY › ENGINE HOOD / DOOR › BACK DOOR CLOSER SYSTEM

BACK DOOR CLOSER SYSTEM > Back Door Closer does not Operate

for Preparation Click here


DESCRIPTION

The power back door ECU controls the back door closer system. In response to the signals output from the switches related to the back door lock, the back door latch activates the closer motor.

HINT:
The back door closer system operates regardless of whether the power back door main switch is ON / OFF.


WIRING DIAGRAM


B120068E02


INSPECTION PROCEDURE

1.INSPECT BACK DOOR LOCK
  1. Check that the back door fully closes (fully locked) when the door is closed by hand.



NG
IMPROPER FIT OF BACK DOOR, OR A FOREIGN OBJECT IS STUCK IN BACK DOOR
OK


2.POWER SOURCE RESET
  1. Disconnect the ECU-B fuse and reconnect it. 10 seconds later, check whether the back door closer is operational.



OK
NORMAL
NG


3.INSPECT BACK DOOR LOCK ASSEMBLY


    B067754E01
  1. Check operation of the door lock.

    1. Using a screwdriver, push the latch in order to put the back door lock in the locked condition (full-latch position).

    2. Connect the battery positive (+) lead to terminal 1 and the battery negative (-) lead to terminal 2. Then, check operation of the latch.

      OK:
      The latch turns to the open-latch position

    3. Inspect motor operation when battery voltage is applied to the terminals.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 2
      Battery negative (-) → Terminal 1
      Clockwise (Motor in normal rotation)
      Battery positive (+) → Terminal 1
      Battery negative (-) → Terminal 2
      Counterclockwise (Motor in reverse rotation)



    B062719E01
  1. Check the back door courtesy switch resistance.

    1. Check the resistance between the terminals of the courtesy switch.

      Resistance:
      Door Lock Latch Position
      Terminal No.
      Specified Condition
      Open-latch position, Half-latch position
      3 - 4
      Below 1 Ω
      Full-latch position, Over-latch position
      10 kΩ or higher

  1. Check the back door latch switch resistance.

    1. Check the resistance between the terminals of the latch switch.

      Resistance:
      Door Lock Latch Position
      Terminal No.
      Specified Condition
      Open-latch position, Over-latch position
      4 - 5
      Below 1 Ω
      Half-latch position, Full-latch position
      10 kΩ or higher

  1. Check the position switch resistance.

    1. Connect the battery positive (+) lead to connector terminal 1 and the negative (-) lead to connector terminal 2.

      Resistance:
      Door Lock Latch Position
      Terminal No.
      Specified Condition
      Any position other than motor stop position (Motor in operation)
      4 - 6
      Below 1 Ω
      Motor stop position (Gear in original position)
      10 kΩ or higher



NG
REPLACE BACK DOOR LOCK ASSEMBLY
OK


4.CHECK WIRE HARNESS (BACK DOOR LOCK ASSEMBLY - POWER BACK DOOR ECU)


    B068432E01
  1. Disconnect the B10 lock and P13 ECU connectors.

  1. Check the resistance between the wire harness side connectors.

    Resistance (Check for open circuit):
    Terminal No.
    Specified Condition
    B10-5 - P13-7 (HAF)
    Below 1 Ω
    B10-6 - P13-21 (POS)
    B10-3 - P13-8 (FUL)
    B10-1 - P13-12 (DC+)
    B10-2 - P13-11 (DC-)

  1. Check the resistance between the B10 lock connector and body ground.

    Resistance (Check for open circuit):
    Terminal No.
    Specified Condition
    B10-4 - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE POWER BACK DOOR ECU