POWER BACK DOOR SYSTEM > Jam Protection Function Activates During Power Back Door Operation |
| 1.CHECK DTC |
Check for DTC B2222. DTC B2222 indicates a pulse sensor malfunction.
Without code outputs, proceed to A.
With code outputs, proceed to B.
|
| ||||
| A | |
| 2.VISUALLY CHECK |
Check for foreign objects on the operating area.
|
| ||||
| OK | |
| 3.MANUAL OPERATION |
Turn off* the power door main switch in order to locate the area where reverse operation has been triggered.
* OFF is the condition when the orange paint on the top of the switch does not appear
Move the back door manually, and then check to make sure no obstacles are present (no extra resistance) around the reverse operation area and that the back door smoothly operates.
|
| ||||
| OK | |
| 4.READ VALUE USING TECHSTREAM |
Using the Techstream, check the DATA LIST for proper functioning of the power back door touch sensor LH.
| Item | Measurement Item / Display (Range) | Normal Condition | Diagnostic Note |
| PBD Touch Sensor (Left) | Power back door touch sensor LH signal / OFF, ON or OPEN | OFF: Power back door touch sensor LH is free ON: Power back door touch sensor LH is pressed OPEN: Power back door touch sensor LH is opened | - |
|
| ||||
| NG | |
| 5.INSPECT POWER BACK DOOR TOUCH SENSOR LH |
![]() |
| Terminal No. | Condition | Specified Condition |
| 1 - 2 | Free | Approx. 1 kΩ |
| Pressed | Less than 100 Ω |
|
| ||||
| OK | |
| 6.CHECK WIRE HARNESS (POWER BACK DOOR TOUCH SENSOR LH - POWER BACK DOOR ECU) |
![]() |
Disconnect the P15 switch and P13 ECU connectors.
Check the resistance between the wire harness side connectors.
| Terminal No. | Specified Condition |
| P15-1 - P13-14 (OSL) | Below 1 Ω |
| P15-2 - P13-15 (OSE) |
|
| ||||
| OK | ||
| ||
| 7.READ VALUE USING TECHSTREAM |
Using the Techstream, check the DATA LIST for proper functioning of the power back door touch sensor RH.
| Item | Measurement Item / Display (Range) | Normal Condition | Diagnostic Note |
| PBD Touch Sensor (Right) | Power back door touch sensor RH signal / OFF, ON or OPEN | OFF: Power back door touch sensor RH is free ON: Power back door touch sensor RH is pressed OPEN: Power back door touch sensor RH is opened | - |
|
| ||||
| NG | |
| 8.CHECK POWER BACK DOOR TOUCH SENSOR RH |
![]() |
| Terminal No. | Condition | Specified Condition |
| 1 - 2 | Free | Approx. 1 kΩ |
| Pressed | Less than 100 Ω |
|
| ||||
| OK | |
| 9.CHECK WIRE HARNESS (POWER BACK DOOR TOUCH SENSOR RH - POWER BACK DOOR ECU) |
![]() |
Disconnect the P16 switch and P13 ECU connectors.
Check the resistance between the wire harness side connectors.
| Terminal No. | Specified Condition |
| P16-1 - P13-16 (OSR) | Below 1 Ω |
| P16-2 - P13-15 (OSE) |
|
| ||||
| OK | ||
| ||
| 10.PERFORM ACTIVE TEST USING TECHSTREAM |
Select the ACTIVE TEST and then check that the power back door drive unit operates.
| Item | Test Details | Diagnostic Note |
| PBD Motor | Power back door motor is operate OFF / FORWARD / REVERSE | Clutch is OFF while power slide door motor is operating |
| PBD Clutch | Power back door clutch is operate OFF / ON | Power slide door motor is OFF when clutch is ON |
|
| ||||
| NG | |
| 11.INSPECT POWER BACK DOOR DRIVE UNIT |
![]() |
Remove the unit.
Connect the battery positive (+) lead to terminal 3 and battery negative (-) terminal lead to terminal 9.
Apply battery voltage to the terminals and check the motor operation.
| Measurement Condition | Specified Condition |
| Battery positive (+) → Terminal 8 Battery negative (-) → Terminal 7 | Open |
| Battery positive (+) → Terminal 7 Battery negative (-) → Terminal 8 | Close |
Check the resistance of the clutch terminals.
| Terminal No. | Specified Condition |
| 3 - 9 | 4.0 Ω |
Reinstall the unit with the connector connected.
![]() |
Check the pulse of the pulse sensor.
Using an oscilloscope, check the pulse generated when the door is manually opened and closed.
| Terminal | Tool setting | Vehicle condition |
| 1 - 6, 5 - 6 | 10 V/DIV., 10 ms/DIV. | Door moving |
|
| ||||
| OK | |
| 12.CHECK WIRE HARNESS (POWER BACK DOOR DRIVE UNIT - POWER BACK DOOR ECU) |
![]() |
Disconnect the P12 unit and P13 ECU connectors.
Check the resistance between the wire harness side connectors.
| Terminal No. | Specified Condition |
| P12-6 (DSG) - P13-23 (DSG) | Below 1 Ω |
| P12-5 (DS2) - P13-24 (DS2) | |
| P12-1 (DS1) - P13-25 (DS1) | |
| P12-2 (DSV) - P13-26 (DSV) |
|
| ||||
| OK | ||
| ||