Home › STEERING › POWER STEERING › RACK AND PINION POWER STEERING GEAR

RACK AND PINION POWER STEERING GEAR > DISASSEMBLY

for Preparation Click here



1. REMOVE RETURN TUBE NO.2


    D030600E01
  1. Using SST, remove the return tube No. 2.

    SST
    09023-12701  



2. REMOVE STEERING LEFT TURN PRESSURE TUBE


    D029981E01
  1. Using SST, remove the left turn pressure tube.

    SST
    09023-38201  

  1. Remove the 2 O-rings from the left turn pressure tube.



3. REMOVE STEERING RIGHT TURN PRESSURE TUBE
SST
09023-38201  

HINT:
Perform the same procedure on the other side.



4. FIX RACK & PINION POWER STEERING GEAR ASSEMBLY


    D030616E01
  1. Using SST, secure the power steering gear assembly.

    SST
    09612-00012  

    HINT:
    Tape the SST before use.



5. REMOVE TIE ROD ASSEMBLY LH


    F040050E11
  1. Place matchmarks on the tie rod assembly and rack end sub-assembly.

  1. Loosen the lock nut, and remove the tie rod assembly and lock nut.



6. REMOVE TIE ROD ASSEMBLY RH

HINT:
Perform the same procedure on the other side.



7. REMOVE STEERING RACK BOOT CLIP
  1. Remove the 2 rack boot clips.



8. REMOVE STEERING RACK BOOT NO.2 CLAMP
  1. Using pliers, remove the rack boot No. 2 clamp.

    NOTICE:
    Be careful not to damage the steering rack boot No. 2.



9. REMOVE STEERING RACK BOOT NO.1 CLAMP

HINT:
Perform the same procedure on the other side.



10. REMOVE STEERING RACK BOOT NO.2


11. REMOVE STEERING RACK BOOT NO.1


12. REMOVE STEERING RACK END SUB-ASSEMBLY


    C083166E06
  1. Using a screwdriver and a hammer, unstake the claw washer.

    NOTICE:
    Avoid any impact to the power steering rack.



    F041526E01
  1. Using 2 SST, remove the 2 steering rack end sub-assembly and 2 claw washers.

    SST
    09922-10010  

    NOTICE:
    1. Use SST 09922-10010 in the direction shown in the illustration.
    2. Securely hold the power steering rack end with a SST.



13. REMOVE RACK GUIDE


    F041500E01
  1. Using SST, remove the rack guide spring cap nut.

    SST
    09922-10010  

    NOTICE:
    Use SST 09922-10010in the direction shown in the illustration.



    F041501E01
  1. Using SST, remove the rack guide spring cap.

    SST
    09631-10021  

  1. Remove the compression spring and the rack guide.



14. REMOVE POWER STEERING CONTROL VALVE


    F041502E01
  1. Using a socket wrench (27 mm), remove the rack housing cap.



    F041503E01
  1. Using SST, hold the control valve and remove the nut.

    SST
    09616-00011  



    F041504E01
  1. Wind vinyl tape around the serrated part of the control valve.

  1. Remove the dust cover from the control valve housing.



    F045545
  1. Remove the 2 bolts and the control valve w/ control valve housing.

  1. Remove the gasket.



    F041506E01
  1. To prevent oil seal lip damage, wind vinyl tape around the serrated part of the control valve.

  1. Using a plastic hammer, remove the control valve w/ oil seal from the control valve housing.

  1. Remove the oil seal from the control valve.



    R011572E06
  1. Using a screwdriver, remove the 4 control valve rings.

    NOTICE:
    Be careful not to damage the grooves for the control valve rings.



15. REMOVE POWER STEERING CONTROL VALVE UPPER OIL SEAL


    F040911E07
  1. Using SST and a press, remove the control valve upper bearing and control valve upper oil seal from the control valve housing.

    SST
    09950-70010   (09951-07150)
    09950-60010   (09951-00250)



16. REMOVE CYLINDER END STOPPER


    C083179E06
  1. Using a screwdriver and a hammer, turn the cylinder end stopper clockwise until the wire end is visible through the service hole.

  1. Using a screwdriver and a hammer, turn the cylinder end stopper counterclockwise, and remove the wire and cylinder end stopper.



17. REMOVE POWER STEERING RACK


18. REMOVE POWER STEERING RACK BUSH


    F040542E06
  1. Remove the rack bush from the power steering rack.

  1. Using SST, remove the rack bush oil seal.

    SST
    09527-21011  
    09612-24014   (09613-22011)

  1. Using a screwdriver, remove the O-ring from the rack bush.



19. REMOVE POWER STEERING CYLINDER TUBE OIL SEAL


    F040544E06
  1. Using SST and a press, remove the cylinder tube oil seal.

    SST
    09950-70010   (09951-07360)
    09950-60010   (09951-00290)



20. REMOVE RACK STEERING PISTON RING


    R010955
  1. Using a screwdriver, remove the rack steering piston ring and O-ring.

    NOTICE:
    Be careful not to damage the grooves for rack steering piston ring.