Home › BODY › SEAT › REAR NO. 2 SEAT ASSEMBLY (w/ Power Stowing Function)

REAR NO. 2 SEAT ASSEMBLY (w/ Power Stowing Function) > Fold Seat Switch Circuit

for Preparation Click here


DESCRIPTION

When the fold seat switch is operated, a switch operation signal is sent to the fold seat control ECU. The ECU receives switch operation signals from each switch and activates the folding motor, reclining motor, and release actuator.

WIRING DIAGRAM


B129640E02


INSPECTION PROCEDURE

1.INSPECT FOLD SEAT CONTROL ECU


    B129650E44
  1. Remove the fold seat control ECU with connectors still connected.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    LH side:
    Tester Connection
    (Symbols)
    Condition
    Specified Condition
    P62-14 (TBL) - Body ground
    Fold seat switch: OFF
    10 to 14 V
    P62-14 (TBL) - Body ground
    Fold seat switch: FOLDING
    Back door: OPEN
    Below 1 V
    P62-15 (RTRN) - Body ground
    Fold seat switch: OFF
    10 to 14 V
    P62-15 (RTRN) - Body ground
    Fold seat switch: RETURN
    Back door: OPEN
    Below 1 V
    P62-16 (FOLD) - Body ground
    Fold seat switch: OFF
    10 to 14 V
    P62-16 (FOLD) - Body ground
    Fold seat switch: STOWING
    Back door: OPEN
    Below 1 V
    RH side:
    Tester Connection
    (Symbols)
    Condition
    Specified Condition
    P64-14 (TBL) - Body ground
    Fold seat switch: OFF
    10 to 14 V
    P64-14 (TBL) - Body ground
    Fold seat switch: FOLDING
    Back door: OPEN
    Below 1 V
    P64-15 (RTRN) - Body ground
    Fold seat switch: OFF
    10 to 14 V
    P64-15 (RTRN) - Body ground
    Fold seat switch: RETURN
    Back door: OPEN
    Below 1 V
    P64-16 (FOLD) - Body ground
    Fold seat switch: OFF
    10 to 14 V
    P64-16 (FOLD) - Body ground
    Fold seat switch: STOWING
    Back door: OPEN
    Below 1 V



OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
NG


2.INSPECT FOLD SEAT SWITCH
  1. Remove the fold seat switch.



    B129653E05
  1. Disconnect the connector from the fold seat switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    LH side:
    Tester Connection
    (Symbols)
    Condition
    Specified Condition
    P60-2 (FOLD) - P60-5 (E)
    Fold seat switch: STOWING
    Below 30 Ω
    P60-7 (RTRN) - P60-5 (E)
    Fold seat switch: RETURN
    Below 30 Ω
    P60-8 (TBL) - P60-5 (E)
    Fold seat switch: FOLDING
    Below 30 Ω
    RH side:
    Tester Connection
    (Symbols)
    Condition
    Specified Condition
    P61-2 (FOLD) - P61-5 (E)
    Fold seat switch: STOWING
    Below 30 Ω
    P61-7 (RTRN) - P61-5 (E)
    Fold seat switch: RETURN
    Below 30 Ω
    P61-8 (TBL) - P61-5 (E)
    Fold seat switch: FOLDING
    Below 30 Ω



NG
REPLACE FOLD SEAT SWITCH
OK


3.CHECK HARNESS AND CONNECTOR (FOLD SEAT SWITCH - FOLD SEAT CONTROL ECU)


    B129654E06
  1. Disconnect the connector from the fold seat control ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    LH side:
    Tester Connection
    (Symbols)
    Condition
    Specified Condition
    P62-16 (FOLD) - P60-2 (FOLD)
    Always
    Below 1 Ω
    P62-15 (RTRN) - P60-7 (RTRN)
    Always
    Below 1 Ω
    P62-14 (TBL) - P60-8 (TBL)
    Always
    Below 1 Ω
    P62-16 (FOLD) - Body ground
    Always
    10 kΩ or higher
    P62-15 (RTRN) - Body ground
    Always
    10 kΩ or higher
    P62-14 (TBL) - Body ground
    Always
    10 kΩ or higher
    RH side:
    Tester Connection
    (Symbols)
    Condition
    Specified Condition
    P64-16 (FOLD) - P61-2 (FOLD)
    Always
    Below 1 Ω
    P64-15 (RTRN) - P61-7 (RTRN)
    Always
    Below 1 Ω
    P64-14 (TBL) - P61-8 (TBL)
    Always
    Below 1 Ω
    P64-16 (FOLD) - Body ground
    Always
    10 kΩ or higher
    P64-15 (RTRN) - Body ground
    Always
    10 kΩ or higher
    P64-14 (TBL) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (BACK DOOR COURTESY SWITCH - FOLD SEAT SWITCH)


    B129655E03
  1. Disconnect the connector from the back door courtesy switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    LH side:
    Tester Connection
    (Symbols)
    Condition
    Specified Condition
    P60-5 (E) - B11-6
    Always
    Below 1 Ω
    P60-5 (E) - Body ground
    Always
    10 kΩ or higher
    RH side:
    Tester Connection
    (Symbols)
    Condition
    Specified Condition
    P61-5 (E) - B11-6
    Always
    Below 1 Ω
    P61-5 (E) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT BACK DOOR COURTESY SWITCH


    B129656E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    B11-6 - B11-5
    Back door: OPEN
    10 kΩ or higher
    B11-6 - B11-5
    Back door: CLOSE
    Below 1 Ω



NG
REPLACE BACK DOOR COURTESY SWITCH
OK


6.CHECK HARNESS AND CONNECTOR (BACK DOOR COURTESY SWITCH - BODY GROUND)


    B129657E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    B11-5 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FOLD SEAT CONTROL ECU