Home › BODY › SEAT › REAR NO. 2 SEAT ASSEMBLY (w/ Power Stowing Function)

REAR NO. 2 SEAT ASSEMBLY (w/ Power Stowing Function) > Folding Motor Circuit

for Preparation Click here


DESCRIPTION

The fold seat control ECU receives a switch operation signal from the fold seat switch and activates the folding motor. At this time, the Hall IC (seat cushion position sensor) detects the actuation signal. The fold seat control ECU uses signals from the Hall IC (seat cushion position sensor) to detect if an object if an object is caught or if any other abnormal condition has occurred.

WIRING DIAGRAM


B129642E03


INSPECTION PROCEDURE

1.INSPECT FOLD SEAT CONTROL ECU


    B129650E45
  1. Remove the fold seat control ECU.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    LH side:
    Tester connection
    (Symbols)
    Condition
    Specified condition
    P63-1 (FLD+) - P63-5 (FLD-)
    Stowing/Return switch: STOWING
    Back door: OPEN
    Ignition switch: OFF
    Park/Neutral switch: P position
    10 to 14 V
    P63-5 (FLD-) - P63-1 (FLD+)
    Stowing/Return switch: RETURN
    Back door: OPEN
    Ignition switch: OFF
    Park/Neutral switch: P position
    10 to 14 V
    P62-23 (SFLD) - P62-30 (SG1)
    Motor is operating
    Below 1 V ←→ 10 to 14 V
    Pulse generation
    P62-24 (SV1) - P62-30 (SG1)
    Back door: OPEN
    9 to 14 V
    RH side:
    Tester connection
    (Symbols)
    Condition
    Specified condition
    P65-1 (FLD+) - P65-5 (FLD-)
    Stowing/Return switch: STOWING
    Back door: OPEN
    Ignition switch: OFF
    Park/Neutral switch: P position
    10 to 14 V
    P65-5 (FLD-) - P65-1 (FLD+)
    Stowing/Return switch: RETURN
    Back door: OPEN
    Ignition switch: OFF
    Park/Neutral switch: P position
    10 to 14 V
    P64-23 (SFLD) - P64-30 (SG1)
    Motor is operating
    Below 1 V ←→ 10 to 14 V
    Pulse generation
    P64-24 (SV1) - P64-30 (SG1)
    Back door: OPEN
    9 to 14 V



OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
NG


2.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - FOLDING MOTOR)


    B129659E21
  1. Disconnect the connector from the fold seat control ECU.

  1. Disconnect the connector from the fold seat motor.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    LH side:
    Tester Connection
    (Symbols)
    Condition
    Specified Condition
    P63-1 (FLD+) - F22-8 (FLD+)
    Always
    Below 1 Ω
    P63-5 (FLD-) - F22-10 (FLD-)
    Always
    Below 1 Ω
    P62-23 (SFLD) - F22-3 (SFLD)
    Always
    Below 1 Ω
    P62-24 (SV1) - F22-6 (PVC1)
    Always
    Below 1 Ω
    P62-30 (SG1) - F22-16 (SGN1)
    Always
    Below 1 Ω
    P63-1 (FLD+) - Body ground
    Always
    10 kΩ or higher
    P63-5 (FLD-) - Body ground
    Always
    10 kΩ or higher
    P62-23 (SFLD) - Body ground
    Always
    10 kΩ or higher
    P62-24 (SV1) - Body ground
    Always
    10 kΩ or higher
    P62-30 (SG1) - Body ground
    Always
    10 kΩ or higher
    RH side:
    Tester Connection
    (Symbols)
    Condition
    Specified Condition
    P65-1 (FLD+) - F23-8 (FLD+)
    Always
    Below 1 Ω
    P65-5 (FLD-) - F23-10 (FLD-)
    Always
    Below 1 Ω
    P64-23 (SFLD) - F23-3 (SFLD)
    Always
    Below 1 Ω
    P64-24 (SV1) - F23-6 (PVC1)
    Always
    Below 1 Ω
    P64-30 (SG1) - F23-16 (SGN1)
    Always
    Below 1 Ω
    P65-1 (FLD+) - Body ground
    Always
    10 kΩ or higher
    P65-5 (FLD-) - Body ground
    Always
    10 kΩ or higher
    P64-23 (SFLD) - Body ground
    Always
    10 kΩ or higher
    P64-24 (SV1) - Body ground
    Always
    10 kΩ or higher
    P64-30 (SG1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE