Home › BODY › SEAT › REAR NO. 2 SEAT ASSEMBLY (w/ Power Stowing Function)

REAR NO. 2 SEAT ASSEMBLY (w/ Power Stowing Function) > Reclining Motor Circuit

for Preparation Click here


DESCRIPTION

The fold seat control ECU receives a switch operation signal from the Power rear No. 2 seat switch and the fold seat switch, and activates the reclining motor. At this time, the Hall IC (seatback position sensor) detects the actuation of the seatback and sends a seatback actuation signal to the fold seat control ECU. The fold seat control ECU uses signals from the Hall IC (seatback position sensor) to detect if an object is caught or if any other abnormal condition has occurred.

WIRING DIAGRAM


B129643E04


INSPECTION PROCEDURE

1.INSPECT FOLD SEAT CONTROL ECU


    B129650E46
  1. Remove the fold seat control ECU with connectors still connected.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    LH side:
    Tester connection
    (Symbols)
    Condition
    Specified condition
    P63-2 (RCL+) - P63-6 (RCL-)
    Power rear No. 2 seat switch: FORWARD
    Back door: OPEN
    Lock switch: UNLOCK
    10 to 14 V
    P63-6 (RCL-) - P63-2 (RCL+)
    Power rear No. 2 seat switch: BACKWARD
    Back door: OPEN
    Lock switch: UNLOCK
    10 to 14 V
    P62-22 (SRCL) - P62-36 (SG2)
    Motor is operating
    Below 1 V ←→ 10 to 14 V
    Pulse generation
    P62-25 (SV2) - P62-36 (SG2)
    Back door: OPEN
    9 to 14 V
    RH side:
    Tester connection
    (Symbols)
    Condition
    Specified condition
    P65-2 (RCL+) - P65-6 (RCL-)
    Power rear No. 2 seat switch: FORWARD
    Back door: OPEN
    Lock switch: UNLOCK
    10 to 14 V
    P65-6 (RCL-) - P65-2 (RCL+)
    Power rear No. 2 seat switch: BACKWARD
    Back door: OPEN
    Lock switch: UNLOCK
    10 to 14 V
    P64-22 (SRCL) - P64-36 (SG2)
    Motor is operating
    Below 1 V ←→ 10 to 14 V
    Pulse generation
    P64-25 (SV2) - P64-36 (SG2)
    Back door: OPEN
    9 to 14 V



OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
NG


2.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - RECLINING MOTOR)


    B129651E13
  1. Disconnect the connectors from the fold seat control ECU.



    B129660E01
  1. Disconnect the connectors from the reclining motor.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    LH side:
    Tester Connection
    (Symbols)
    Condition
    Specified Condition
    P63-2 (RCL+) - P66-1
    Always
    Below 1 Ω
    P63-6 (RCL-) - P66-2
    Always
    Below 1 Ω
    P62-22 (SRCL) - P67-1 (OUTPUT)
    Always
    Below 1 Ω
    P62-25 (SV2) - P67-3 (VCC)
    Always
    Below 1 Ω
    P62-36 (SG2) - P67-2 (GND)
    Always
    Below 1 Ω
    P63-2 (RCL+) - Body ground
    Always
    10 kΩ or higher
    P63-6 (RCL-) - Body ground
    Always
    10 kΩ or higher
    P62-22 (SRCL) - Body ground
    Always
    10 kΩ or higher
    P62-25 (SV2) - Body ground
    Always
    10 kΩ or higher
    P62-36 (SG2) - Body ground
    Always
    10 kΩ or higher
    RH side:
    Tester Connection
    (Symbols)
    Condition
    Specified Condition
    P65-2 (RCL+) - P68-1
    Always
    Below 1 Ω
    P65-6 (RCL-) - P68-2
    Always
    Below 1 Ω
    P64-22 (SRCL) - P69-1 (OUTPUT)
    Always
    Below 1 Ω
    P64-25 (SV2) - P69-3 (VCC)
    Always
    Below 1 Ω
    P64-36 (SG2) - P69-2 (GND)
    Always
    Below 1 Ω
    P65-2 (RCL+) - Body ground
    Always
    10 kΩ or higher
    P65-6 (RCL-) - Body ground
    Always
    10 kΩ or higher
    P64-22 (SRCL) - Body ground
    Always
    10 kΩ or higher
    P64-25 (SV2) - Body ground
    Always
    10 kΩ or higher
    P64-36 (SG2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT RECLINING MOTOR


    B168181E01
  1. Check reclining motor operation.

    1. Check if the motor rotates smoothly when the battery is connected to the reclining motor.

      OK:
      LH side:
      Measurement Condition
      Specified Condition
      Battery positive (+) →P66-1
      Battery negative (-) → P66-2
      FORWARD
      Battery positive (+) →P66-2
      Battery negative (-) → P66-1
      BACKWARD
      RH side:
      Measurement Condition
      Specified Condition
      Battery positive (+) →P68-1
      Battery negative (-) → P68-2
      FORWARD
      Battery positive (+) →P68-2
      Battery negative (-) → P68-1
      BACKWARD



NG
REPLACE RECLINING MOTOR
OK

REPLACE FOLD SEAT CONTROL ECU