Home › BODY › SEAT › REAR NO. 2 SEAT ASSEMBLY (w/ Power Stowing Function)

REAR NO. 2 SEAT ASSEMBLY (w/ Power Stowing Function) > Rear Power Seat Switch Circuit

for Preparation Click here


DESCRIPTION

When the power rear No. 2 seat switch is operated, a recline signal is sent to the fold seat control ECU. The ECU activates the reclining motor based on the signal from power rear No. 2 seat switch.

WIRING DIAGRAM


B129648E03


INSPECTION PROCEDURE

1.INSPECT FOLD SEAT CONTROL ECU


    B129650E48
  1. Remove the fold seat control ECU.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    LH side:
    Tester connection
    (Symbols)
    Condition
    Specified condition
    P62-12 (RCLF) - Body ground
    Always
    10 to 14 V
    P62-12 (RCLF) - Body ground
    Power rear No. 2 seat switch: FORWARD
    Below 1 V
    P62-13 (RCLR) - Body ground
    Always
    10 to 14 V
    P62-13 (RCLR) - Body ground
    Power rear No. 2 seat switch: BACKWARD
    Below 1 V
    RH side:
    Tester connection
    (Symbols)
    Condition
    Specified condition
    P64-12 (RCLF) - Body ground
    Always
    10 to 14 V
    P64-12 (RCLF) - Body ground
    Power rear No. 2 seat switch: FORWARD
    Below 1 V
    P64-13 (RCLR) - Body ground
    Always
    10 to 14 V
    P64-13 (RCLR) - Body ground
    Power rear No. 2 seat switch: BACKWARD
    Below 1 V



OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
NG


2.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - FOLDING MOTOR)


    B168173E02
  1. Disconnect the connectors from the fold seat control ECU.

  1. Disconnect the connector from the folding motor.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    LH side:
    Tester connection
    (Symbols)
    Condition
    Specified condition
    P62-12 (RCLF) - F22-4 (RCLF)
    Always
    Below 1 Ω
    P62-13 (RCLR) - F22-13 (RCLR)
    Always
    Below 1 Ω
    P62-12 (RCLF) - Body ground
    Always
    10 kΩ or higher
    P62-13 (RCLR) - Body ground
    Always
    10 kΩ or higher
    RH side:
    Tester connection
    (Symbols)
    Condition
    Specified condition
    P64-12 (RCLF) - F23-4 (RCLF)
    Always
    Below 1 Ω
    P64-13 (RCLR) - F23-13 (RCLR)
    Always
    Below 1 Ω
    P64-12 (RCLF) - Body ground
    Always
    10 kΩ or higher
    P64-13 (RCLR) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT FOLD SEAT SWITCH


    B129668E02
  1. Disconnect the connector from the power rear No. 2 seat switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    LH side:
    Tester connection
    (Symbols)
    Condition
    Specified condition
    4 (RCLF) - 3 (E)
    Always
    10 kΩ or higher
    4 (RCLF) - 3 (E)
    Power rear No. 2 seat switch: FORWARD
    Below 1 Ω
    1 (RCLR) - 3 (E)
    Always
    10 kΩ or higher
    1 (RCLR) - 3 (E)
    Power rear No. 2 seat switch: BACKWARD
    Below 1 Ω
    RH side:
    Tester connection
    (Symbols)
    Condition
    Specified condition
    4 (RCLF) - 3 (E)
    Always
    10 kΩ or higher
    4 (RCLF) - 3 (E)
    Power rear No. 2 seat switch: FORWARD
    Below 1 Ω
    1 (RCLR) - 3 (E)
    Always
    10 kΩ or higher
    1 (RCLR) - 3 (E)
    Power rear No. 2 seat switch: BACKWARD
    Below 1 Ω



NG
REPLACE POWER REAR NO. 2 SEAT SWITCH
OK


4.CHECK HARNESS AND CONNECTOR (FOLDING MOTOR - BODY GROUND)


    B129662E03
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    LH side:
    Tester connection
    (Symbols)
    Condition
    Specified condition
    F22-1 (E) - Body ground
    Always
    Below 1 Ω
    RH side:
    Tester connection
    (Symbols)
    Condition
    Specified condition
    F23-1 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.REPAIR OR REPLACE HARNESS OR CONNECTOR (WIRE INSIDE SEAT)
  1. Repair or replace harness or connector (wire inside seat) and check that the malfunction disappears.

    OK:
    Malfunction disappears.



NG
REPLACE FOLD SEAT CONTROL ECU
OK

END