Home › BODY › SEAT › REAR NO. 2 SEAT ASSEMBLY (w/ Power Stowing Function)

REAR NO. 2 SEAT ASSEMBLY (w/ Power Stowing Function) > Fold Lock Switch Circuit

for Preparation Click here


DESCRIPTION

Each of the left and right seats has a fold lock switch that detects the lock condition of the seat legs and floor when the seat is in the stowed state. If the fold lock switch detects an unlock condition, the 3rd SEAT indicator on the combination meter will come on.

WIRING DIAGRAM


B129649E02


INSPECTION PROCEDURE

1.INSPECT FOLD SEAT CONTROL ECU


    B129650E49
  1. Remove the fold seat control ECU with connectors still connected.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    LH side 
    Tester Connection
    (Symbols)
    Condition
    Specified Condition
    P62-37 (LCKR) - Body ground
    Fold lock switch: UNLOCK
    Below 1 V
    P62-37 (LCKR) - Body ground
    Fold lock switch: LOCK
    10 to 14 V
    RH side 
    Tester Connection
    (Symbols)
    Condition
    Specified Condition
    P64-37 (LCKR) - Body ground
    Fold lock switch: UNLOCK
    Below 1 V
    P64-37 (LCKR) - Body ground
    Fold lock switch: LOCK
    10 to 14 V



OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
NG


2.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - FOLD LOCK SWITCH)


    B129659E24
  1. Disconnect the connectors from the fold seat control ECU.

  1. Disconnect the connector from the fold lock switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    LH side 
    Tester Connection
    (Symbols)
    Condition
    Condition
    P62-37 (LCKR) - F22-15 (LCKR)
    Always
    Below 1 Ω
    P62-37 (LCKR) - Body ground
    Always
    10 kΩ or higher
    RH side 
    Tester Connection
    (Symbols)
    Condition
    Condition
    P64-37 (LCKR) - F23-15 (LCKR)
    Always
    Below 1 Ω
    P64-37 (LCKR) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (FOLD LOCK SWITCH - BODY GROUND)


    B129662E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    LH side 
    Tester Connection
    (Symbols)
    Condition
    Specified Condition
    F22-1 (E) - Body ground
    Always
    Below 1 Ω
    RH side 
    Tester Connection
    (Symbols)
    Condition
    Specified Condition
    F23-1 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT FOLD LOCK SWITCH


    B129721E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    LH side 
    Tester Connection
    (Symbols)
    Condition
    Specified Condition
    F22-15 (LCKR) - F22-1 (E)
    Fold lock switch: UNLOCK
    Below 1 Ω
    F22-15 (LCKR) - F22-1 (E)
    Fold lock switch: LOCK
    10 kΩ or higher
    RH side 
    Tester Connection
    (Symbols)
    Condition
    Specified Condition
    F23-15 (LCKR) - F23-1 (E)
    Fold lock switch: UNLOCK
    Below 1 Ω
    F23-15 (LCKR) - F23-1 (E)
    Fold lock switch: LOCK
    10 kΩ or higher



NG
REPLACE FOLD LOCK SWITCH
OK

REPLACE FOLD SEAT CONTROL ECU