Home › BODY › SEAT › FRONT SEAT ASSEMBLY (for Manual Seat)

FRONT SEAT ASSEMBLY (for Manual Seat) > DISASSEMBLY

for Preparation Click here



1. REMOVE FRONT SEAT SIDE TABLE LEG COVER (w/ Table)
  1. Using a screwdriver, disengage the claws and remove the seat side table leg cover.

    HINT:
    Tape the screwdriver tip before use.



2. REMOVE FRONT SEAT SIDE TABLE (w/ Table)
  1. Remove the 4 nuts and seat side table.

  1. Remove the 2 clips and seat side table cover.



3. REMOVE OCCUPANT CLASSIFICATION ECU (for Front Passenger Seat)
  1. Disconnect the 2 connectors from the occupant classification ECU.



    H045345
  1. Using a screwdriver, remove the occupant classification ECU.



4. REMOVE VERTICAL SEAT ADJUSTER KNOB (for Driver Seat)
  1. Using a scraper, disengage the claws and remove the vertical seat adjuster knob cover.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the screw and the vertical seat adjuster knob.



5. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH


    B067433
  1. Using a screwdriver, disengage the claws and remove the reclining adjuster release handle.

    HINT:
    Tape the screwdriver tip before use.



6. REMOVE FRONT SEAT CUSHION SHIELD LH
  1. Remove the screw.

  1. Using a screwdriver, disengage the claws and remove the cushion shield.

    HINT:
    Tape the screwdriver tip before use.



7. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH
  1. Disconnect the connectors.

  1. Remove the nut and inner belt assembly.



8. REMOVE FRONT SEAT CUSHION SHIELD INNER LH
  1. Remove the screw.

  1. Using a screwdriver, disengage the claws and remove the cushion shield.

    HINT:
    Tape the screwdriver tip before use.



9. REMOVE FRONT SEAT TRACK COVER LH FRONT OUTER
  1. Remove the clip, 2 screws and seat track cover front outer.



10. REMOVE FRONT SEAT TRACK COVER LH FRONT INNER
  1. Remove the clip, 2 screws and seat track cover front inner.



11. REMOVE FRONT SEAT INNER LH ARMREST ASSEMBLY


    B067260
  1. Using a screwdriver, remove the armrest cap.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the bolt and armrest.

  1. Remove the 2 washers and 2 spacers.



12. REMOVE SEAT CUSHION COVER WITH PAD


    B086914
  1. Disengage the clamps and hooks.

  1. Disengage the hooks and remove the seat cushion cover with pad.



13. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER
  1. Remove the hog rings and the separate type front seat cushion cover.



14. REMOVE FRONT SEATBACK BOARD LH


    B090157E01
  1. Disengage the clips.

  1. Remove the seatback board by pulling it out in the arrow mark direction shown in the illustration.



15. REMOVE LUMBAR SUPPORT KNOB LH (for Driver Seat)


    B067263
  1. Using a shop rag, remove the snap ring and lumbar support knob.



16. REMOVE FRONT SEAT HEADREST SUPPORT


    B060977
  1. Disengage the claw and remove the 2 headrest supports.



17. REMOVE SEATBACK COVER WITH PAD


    B086918
  1. with Side airbag:
    Remove the nut and disengage the separate type front seatback cover bracket.

  1. Remove the hog rings and disengage the hooks.



    B086920
  1. Remove the seatback cover with pad.



18. REMOVE FRONT SEATBACK COVER LH
  1. Remove the hog rings and the front seatback cover.



19. REMOVE RECLINING ADJUSTER INSIDE COVER LH


    B120079E01
  1. Disengage the clamp.

  1. Remove the screw and the reclining adjuster inside cover LH (lower).



20. REMOVE RECLINING ADJUSTER INSIDE COVER RH

HINT:
Use the same procedures for the RH side and LH side.



21. REMOVE RECLINING ADJUSTER INSIDE COVER LH


    B086923
  1. Remove the screw and the reclining adjuster inside cover LH (upper).



22. REMOVE RECLINING ADJUSTER INSIDE COVER RH

HINT:
Use the same procedures for the RH side and LH side.



23. REMOVE FRONT SEAT CUSHION SHIELD LOWER LH


    B086924
  1. Remove the screw and the front seat cushion shield lower LH.



24. REMOVE FRONT SEAT CUSHION SHIELD LOWER RH

HINT:
Use the same procedures for the RH side and LH side.



25. REMOVE SEAT POSITION AIRBAG SENSOR (for Driver Seat)
  1. Disconnect the connector from the seat position sensor.



    H045347E01
  1. Using a "torx" socket wrench (T30), remove the "torx" screw and the seat position sensor.