FRONT SEAT ASSEMBLY (for Manual Seat) > REASSEMBLY |
| 1. INSTALL SEAT POSITION AIRBAG SENSOR (for Driver Seat) |
Check that the ignition switch is off.
Check that the negative battery (-) terminal is disconnected.
![]() |
Using a feeler gauge 1 mm (0.039 in.), install the seat position sensor.
Using a "torx" socket wrench (T30), tighten the "torx" screw to install the seat position sensor.
Make sure that a clearance between the seat position sensor and the seat rail is within 0.6 mm (0.023 in.) to 1.4 mm (0.055 in.).
Check that there is no looseness in the installation parts of the seat position sensor.
Connect the connector to the seat position sensor.
| 2. INSTALL FRONT SEAT CUSHION SHIELD LOWER LH |
Install the front seat cushion shield lower LH with the screw.
| 3. INSTALL FRONT SEAT CUSHION SHIELD LOWER RH |
| 4. INSTALL RECLINING ADJUSTER INSIDE COVER LH |
Install the reclining adjuster inside cover LH (upper) with the screw.
| 5. INSTALL RECLINING ADJUSTER INSIDE COVER RH |
| 6. INSTALL RECLINING ADJUSTER INSIDE COVER LH |
Install the reclining adjuster inside cover LH (lower) with the screw.
Install the clamp.
| 7. INSTALL RECLINING ADJUSTER INSIDE COVER RH |
| 8. INSTALL FRONT SEATBACK COVER LH |
![]() |
Install the seatback pad.
Cover the top of the seatback pad with the seatback cover.
Using hog ring pliers, completely install the seatback cover with new hog rings.
| 9. INSTALL SEATBACK COVER WITH PAD |
![]() |
Install the seatback cover with pad.
![]() |
Using hog ring pliers, install new hog rings and hooks.
with Side airbag:
Install the seatback cover bracket with the nut.
![]() |
Engage the rubber wire with a hole of the front seatback frame with new hog rings, as shown in the illustration.
Using hog ring pliers, install new hog rings.
| 10. INSTALL FRONT SEAT HEADREST SUPPORT |
Install the 2 headrest supports.
| 11. INSTALL LUMBAR SUPPORT KNOB LH (for Driver Seat) |
Install the lumbar support knob with the snap ring.
| 12. INSTALL FRONT SEATBACK BOARD LH |
Install the seatback board LH.
| 13. INSTALL SEAT CUSHION COVER WITH PAD |
Install the seat cushion cover with pad.
Install the clamps and hooks.
| 14. INSTALL FRONT SEAT INNER LH ARMREST ASSEMBLY |
Install the armrest with the bolt.
Install the seat armrest cap.
| 15. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER |
![]() |
Install the seat cushion pad to the seat cushion cover.
Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.
| 16. INSTALL FRONT SEAT TRACK COVER LH FRONT INNER |
Install the seat track cover LH front inner with the clip and 2 screws.
| 17. INSTALL FRONT SEAT TRACK COVER LH FRONT OUTER |
Install the seat track cover LH front outer with the clip and 2 screws.
| 18. INSTALL FRONT SEAT CUSHION SHIELD INNER LH |
Install the cushion shield.
Install the screw.
| 19. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH |
Install the inner belt assembly with the nut.
Connect the connectors.
| 20. INSTALL FRONT SEAT CUSHION SHIELD LH |
Install the front seat cushion shield LH.
Install the screw.
| 21. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH |
Install the reclining adjuster release handle LH.
| 22. INSTALL VERTICAL SEAT ADJUSTER KNOB (for Driver Seat) |
Install the vertical seat adjuster knob with the screw.
Install the vertical seat adjuster knob cover.
| 23. INSTALL OCCUPANT CLASSIFICATION ECU (for Front Passenger Seat) |
Check that the ignition switch is off.
Check that the negative battery (-) terminal is disconnected.
![]() |
Install the occupant classification ECU.
Connect the 2 connectors to the occupant classification ECU.
| 24. INSTALL FRONT SEAT SIDE TABLE (w/ Table) |
Install the seat side table with 4 nuts.
| 25. INSTALL FRONT SEAT SIDE TABLE LEG COVER (w/ Table) |
Install the front seat side table leg cover.