FRONT SEAT ASSEMBLY (for Power Seat) > DISASSEMBLY |
| 1. REMOVE FRONT SEAT SIDE TABLE LEG COVER (w/ Table) |
Using a screwdriver, disengage the claws and remove the seat side table leg cover.
| 2. REMOVE FRONT SEAT SIDE TABLE (w/ Table) |
Remove the 4 nuts and seat side table.
Remove the 2 clips and seat side table cover.
| 3. REMOVE OCCUPANT CLASSIFICATION ECU (for Front Passenger Seat) |
Disconnect the 2 connectors from the occupant classification ECU.
![]() |
Using a screwdriver, remove the occupant classification ECU.
| 4. REMOVE RECLINING POWER SEAT SWITCH KNOB |
![]() |
Using a screwdriver, remove the reclining power seat switch knob.
| 5. REMOVE SLIDE & VERTICAL POWER SEAT SWITCH KNOB |
Using a screwdriver, remove the slide & vertical power seat switch knob.
| 6. REMOVE FRONT SEAT CUSHION SHIELD INNER LH |
Remove the 7 screws.
Using a screwdriver, disengage the 4 claws and clip, and remove the front seat cushion shield LH together with the front seat cushion shield inner LH and front seat cushion shield inner No. 1 LH.

Remove the screw and front seat cushion shield inner LH from the front seat cushion shield inner No. 1 LH.
| 7. REMOVE NO. 1 FRONT SEAT CUSHION SHIELD INNER LH |
Remove the screw and front seat cushion shield inner No. 1 LH from the front seat cushion shield LH.
| 8. REMOVE POWER SEAT SWITCH (for Driver Seat) |
![]() |
Remove the 2 screws and the power seat switch.
| 9. REMOVE FRONT POWER SEAT SWITCH LH |
Disconnect the connector.
Remove the 3 screws and power seat switch LH.
| 10. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH |
Disconnect the connectors.
Remove the nut and inner belt assembly.
| 11. REMOVE FRONT SEAT TRACK COVER LH FRONT OUTER |
Remove the clip, 2 screws and seat track cover front outer.
| 12. REMOVE FRONT SEAT TRACK COVER LH FRONT INNER |
Remove the clip, 2 screws and seat track cover front inner.
| 13. REMOVE FRONT SEAT INNER LH ARMREST ASSEMBLY |
![]() |
Using a screwdriver, pry out the armrest cap.
Remove the bolt and armrest assembly.
Remove the 2 washers and 2 spacers.
| 14. REMOVE SEAT CUSHION COVER WITH PAD |
![]() |
with Seat heater:
Disconnect the connector.
Disengage the clamps and hooks.
Disengage the hooks and remove the seat cushion cover with pad.
| 15. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER |
Remove the hog rings and the separate type front seat cushion cover.
| 16. REMOVE FRONT SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System) |
Cut off the tack pins which fasten the seat heater and then remove the front seat heater from the cushion cover.
| 17. REMOVE FRONT SEATBACK BOARD LH |
![]() |
Disengage the clips.
Remove the seatback board by pulling it out in the arrow mark direction shown in the illustration.
| 18. REMOVE FRONT SEAT HEADREST SUPPORT |
![]() |
Disengage the claw and remove the 2 headrest supports.
| 19. REMOVE SEATBACK COVER WITH PAD |
![]() |
with Side airbag:
Remove the nut and disengage the separate type front seatback cover bracket.
Remove the hog rings and disengage the hooks.
![]() |
Remove the seatback cover with pad.
| 20. REMOVE FRONT SEATBACK COVER LH |
Remove the hog rings and the front seatback cover.
| 21. REMOVE FRONT SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System) |
Cut off the tack pins which fasten the seat heater and then remove the front seat heater from the front seatback cover.
| 22. REMOVE RECLINING ADJUSTER INSIDE COVER LH |
![]() |
Remove the 2 screws and the reclining adjuster inside cover LH (lower).
| 23. REMOVE RECLINING ADJUSTER INSIDE COVER RH |
![]() |
Disengage the clamp.
Remove the 2 screws and the reclining adjuster inside cover RH (lower).
| 24. REMOVE RECLINING ADJUSTER INSIDE COVER LH |
![]() |
Remove the screw and the reclining adjuster inside cover LH (upper).
| 25. REMOVE RECLINING ADJUSTER INSIDE COVER RH |
| 26. REMOVE FRONT SEAT CUSHION SHIELD LOWER LH |
![]() |
Remove the screw and the front seat cushion shield lower LH.
| 27. REMOVE FRONT SEAT CUSHION SHIELD LOWER RH |
| 28. REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (for Driver Seat) |
![]() |
Disconnect the connector.
Remove the 2 screws and the lumbar support adjuster assembly LH.
| 29. REMOVE SEAT POSITION AIRBAG SENSOR (for Driver Seat) |
Disconnect the connector from the seat position sensor.
![]() |
Using a "torx" socket wrench (T30), remove the "torx" screw and the seat position sensor.