Home › BODY › SEAT › FRONT SEAT ASSEMBLY (for Power Seat)

FRONT SEAT ASSEMBLY (for Power Seat) > REASSEMBLY

for Preparation Click here



1. INSTALL SEAT POSITION AIRBAG SENSOR (for Driver Seat)
  1. Check that the ignition switch is off.

  1. Check that the negative battery (-) terminal is disconnected.

    CAUTION:
    After disconnecting the negative battery terminal, wait for at least 90 seconds before starting the operation.



    H043794E03
  1. Using a feeler gauge 1 mm (0.039 in.), install the seat position sensor.

    NOTICE:
    1. If the seat position sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
    2. When installing the seat position sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

    HINT:
    Be sure that a clearance between the seat position sensor and the seat rail is within 0.6 mm (0.023 in.) to 1.4 mm (0.055 in.).

  1. Using a "torx" socket wrench (T30), tighten the "torx" screw to install the seat position sensor.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Make sure that a clearance between the seat position sensor and the seat rail is within 0.6 mm (0.023 in.) to 1.4 mm (0.055 in.).

  1. Check that there is no looseness in the installation parts of the seat position sensor.

  1. Connect the connector to the seat position sensor.



2. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH
  1. Install the seat side table leg cover.



3. INSTALL FRONT SEAT CUSHION SHIELD LOWER LH
  1. Install the front seat cushion shield lower LH with the screw.



4. INSTALL FRONT SEAT CUSHION SHIELD LOWER RH

HINT:
Use the same procedures for the RH side and LH side.



5. INSTALL RECLINING ADJUSTER INSIDE COVER LH
  1. Install the reclining adjuster inside cover LH (upper) with the screw.



6. INSTALL RECLINING ADJUSTER INSIDE COVER RH

HINT:
Use the same procedures for the RH side and LH side.



7. INSTALL RECLINING ADJUSTER INSIDE COVER RH
  1. Install the reclining adjuster inside cover RH (lower) with the 2 screws.

  1. Install the clamp.



8. INSTALL RECLINING ADJUSTER INSIDE COVER LH
  1. Install the reclining adjuster inside cover LH (lower) with the 2 screws.



9. INSTALL FRONT SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System)
  1. Place the seat heater on the seatback cover.



  1. Install the seat heater to the seatback cover with new tack pins.


    B067265E01

    NOTICE:
    Do not substitute other metal parts for tack pins.



10. INSTALL FRONT SEATBACK COVER LH


    B050126E02
  1. Install the seatback pad.

  1. Cover the top of the seatback pad with the seatback cover.

  1. Using hog ring pliers, completely install the seatback cover with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to prevent wrinkles as much as possible.



11. INSTALL SEATBACK COVER WITH PAD


    B086920
  1. Install the seatback cover with pad.



    B050126E02
  1. Using hog ring pliers, install new hog rings and hooks.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.



    B086918
  1. with Side airbag:
    Install the seatback cover bracket with the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 48 in.*lbf }

    NOTICE:
    1. For a vehicle with side airbag, the side airbag may not be activated normally unless the seatback cover is securely installed.
    2. Check that the strap has no twist after installing the bracket.



    B067266E01
  1. Attach a rubber wire with new hog rings, as shown in the illustration.

  1. Using hog ring pliers, install new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to prevent wrinkles as much as possible.



12. INSTALL FRONT SEAT HEADREST SUPPORT
  1. Install the 2 headrest supports.



13. INSTALL FRONT SEATBACK BOARD LH


    B203071E02
  1. Engage the 4 claws and 2 clips to install the front seatback board LH.



14. INSTALL FRONT SEAT INNER LH ARMREST ASSEMBLY
  1. Install the armrest with the bolt.

    Torque:
    20 N*m{ 200 kgf*cm , 14 ft.*lbf }

  1. Install the armrest cap.



15. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System)
  1. Place the seat heater on the seat cushion cover.



  1. Install the seat heater to the seat cushion cover with new tack pins.


    B067267E01

    NOTICE:
    Do not substitute other metal parts for tack pins.



16. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER


    B050126E02
  1. Install the seat cushion pad to the seat cushion cover.

  1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to prevent wrinkles as much as possible.



17. INSTALL SEAT CUSHION COVER WITH PAD
  1. Install the seat cushion cover with pad.

  1. Install the clamps and hooks.

  1. with Seat heater:
    Connect the connector.



18. INSTALL FRONT SEAT TRACK COVER LH FRONT INNER
  1. Install the seat track cover front inner with the clip and 2 screws.



19. INSTALL FRONT SEAT TRACK COVER LH FRONT OUTER
  1. Install the seat track cover front outer with the clip and 2 screws.



20. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH
  1. Install the inner belt assembly with the nut.

    Torque:
    41 N*m{ 418 kgf*cm , 30 ft.*lbf }

    HINT:
    Check that the inner seat belt assembly moves smoothly.

  1. Connect the connectors.



21. INSTALL FRONT POWER SEAT SWITCH LH
  1. Install the power seat switch LH with the 3 screws.

  1. Connect the connector.



22. INSTALL POWER SEAT SWITCH (for Driver Seat)
  1. Install the power seat switch with the 2 screws.



23. INSTALL NO. 1 FRONT SEAT CUSHION SHIELD INNER LH
  1. Install the No. 1 front seat cushion shield inner LH to the front seat cushion shield LH with the screw.



24. INSTALL FRONT SEAT CUSHION SHIELD INNER LH
  1. Install the front seat cushion shield inner LH to the No. 1 front seat cushion shield inner LH with the screw.

  1. Install the front seat cushion shield LH together with front seat cushion shield inner LH and No. 1 front seat cushion shield inner LH.

  1. Install the 7 screws.



25. INSTALL SLIDE & VERTICAL POWER SEAT SWITCH KNOB
  1. Install the reclining power seat switch knob.



26. INSTALL RECLINING POWER SEAT SWITCH KNOB
  1. Install the reclining power seat switch knob.



27. INSTALL OCCUPANT CLASSIFICATION ECU (for Front Passenger Seat)
  1. Check that the ignition switch is off.

  1. Check that the negative battery (-) terminal is disconnected.

    CAUTION:
    After disconnecting the negative battery terminal, wait for at least 90 seconds before starting the operation.



    H045345
  1. Install the occupant classification ECU.

  1. Connect the 2 connectors to the occupant classification ECU.

    NOTICE:
    1. If the occupant classification ECU has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
    2. When installing the occupant classification ECU, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.



28. INSTALL FRONT SEAT SIDE TABLE (w/ Table)
  1. Install the seat side table with 4 nuts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



29. INSTALL FRONT SEAT SIDE TABLE LEG COVER (w/ Table)
  1. Install the seat side table leg cover.