Home › ENGINE › 2GR-FE ENGINE MECHANICAL › ENGINE ASSEMBLY

ENGINE ASSEMBLY > REMOVAL

for Preparation Click here



1. DISCHARGE FUEL SYSTEM PRESSURE

HINT:
Click here.



2. DISCHARGE REFRIGERANT FROM REFRIGERATION SYSTEM
  1. Turn the A/C switch to ON.

  1. Operating the cooler compressor at the engine rpm of approx. 1,000 for 5 to 6 minutes, circulate the refrigerant and collect the compressor oil remaining in each component into the cooler compressor as much as possible.

  1. Stop the engine.

  1. Recover the refrigerant from the A/C system using a refrigerant recovery unit.



3. REMOVE BATTERY


    A155033
  1. Disconnect the negative battery terminal.

  1. Disconnect the positive battery terminal.

  1. Loosen the nut, and remove the bolt and battery clamp.

  1. Remove the battery and battery tray.



4. PLACE FRONT WHEELS FACING STRAIGHT AHEAD


5. REMOVE FRONT WHEELS


6. REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY


    A162362
  1. Remove the 8 bolts, 4 clips and No. 1 engine under cover assembly.



7. REMOVE FRONT FENDER APRON SEAL RH


    A162371
  1. Remove the 2 bolts, clip and front fender apron seal RH.



8. REMOVE FRONT FENDER APRON SEAL LH


    A162370
  1. Remove the 2 bolts, clip and front fender apron seal LH.



9. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil drain plug, and drain the oil into a container.

  1. Clean and install the oil drain plug with a new gasket.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



10. DRAIN ENGINE COOLANT


  1. Loosen the radiator drain cock plug.


    A161473E01

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Remove the radiator cap sub-assembly from the radiator assembly.

    NOTICE:
    Do not remove the radiator cap sub-assembly while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the 2 cylinder block drain cock plugs.



11. DRAIN AUTOMATIC TRANSAXLE FLUID
  1. Remove the drain plug, gasket and drain ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }



12. REMOVE FRONT WIPER ARM HEAD CAP


    I035789E01
  1. Using a small screwdriver, remove the 2 front wiper arm covers.

    HINT:
    Tape up the screwdriver tip before use.



13. REMOVE WINDSHIELD WIPER ARM AND BLADE ASSEMBLY RH
  1. Operate the wiper, and stop the windshield wiper motor assembly to the automatic stop position.

  1. Remove the nut and the FR wiper arm RH.



14. REMOVE WINDSHIELD WIPER ARM AND BLADE ASSEMBLY LH
  1. Remove the nut and the FR wiper arm LH.



15. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    I035790E01
  1. Remove the 6 claws and the cowl top ventilator louver sub-assembly.



16. REMOVE FRONT WIPER MOTOR AND LINK ASSEMBLY
  1. Disconnect the connector.



    I035791E01
  1. Remove the 4 bolts and wiper motor & link assembly.



17. REMOVE NO. 1 COWL TOP TO COWL BRACE INNER


    A162366
  1. Remove the 2 bolts, 2 clips and No. 1 cowl top to cowl brace inner.



18. REMOVE FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY


    A162375
  1. Remove the nut, and separate the fuel pump resistor.



    A162368
  1. Remove the 2 clips, and separate the engine wire.



    A162367
  1. Remove the 7 bolts and front outer cowl top panel sub-assembly.



19. REMOVE V-BANK COVER SUB-ASSEMBLY


    A162365
  1. Hold the front of the V-bank cover and raise it to disengage the 2 clips on the front of the cover. Continue to raise the cover to disengage the clip on the rear of the cover and remove the cover.

    NOTICE:
    Attempting to disengage both front and rear clips at the same time may cause the cover to break.



20. REMOVE NO. 2 AIR CLEANER INLET


    A133004
  1. Disconnect the vacuum switching valve clamp.

  1. Disconnect the 2 vacuum hoses.

  1. Remove the 2 bolts and No. 2 air cleaner inlet.



21. REMOVE NO. 1 AIR CLEANER INLET


    A155040
  1. Remove the bolt and No. 1 air cleaner inlet.



22. REMOVE AIR CLEANER CAP SUB-ASSEMBLY


    A162723E01
  1. Disconnect the 3 vacuum hoses.



    A162726
  1. Loosen the bolt, disconnect the 2 connectors, and remove the 2 vacuum hoses.



    A161845
  1. Remove the 2 bolts, air cleaner cap sub-assembly, and air cleaner filter element.



23. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
  1. Remove the air cleaner filter element sub-assembly.



24. REMOVE AIR CLEANER CASE SUB-ASSEMBLY


    A155039
  1. Disconnect the vacuum switching valve connector.

  1. Disconnect the vacuum hose.

  1. Remove the 3 bolts and air cleaner case.



25. REMOVE AIR CLEANER BRACKET


    A155041
  1. Remove the 2 bolts and air cleaner bracket.



26. REMOVE INTAKE AIR RESONATOR SUB-ASSEMBLY


    A155042
  1. Remove the clip, bolt and intake air resonator.



27. REMOVE NO. 2 ENGINE MOUNTING STAY RH


    A139217
  1. Remove bolt, 2 nuts and No. 2 engine mounting stay RH.



28. REMOVE ENGINE MOVING CONTROL ROD


    A162369
  1. Remove the 3 bolts and engine moving control rod.



29. DISCONNECT NO. 1 FUEL VAPOR FEED HOSE


    A155036
  1. Remove the clamp and disconnect the No. 1 fuel vapor feed hose.



30. DISCONNECT RADIATOR INLET HOSE


    A155046
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect radiator inlet hose from the water outlet.



31. DISCONNECT RADIATOR OUTLET HOSE


    A155038
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect the radiator outlet hose from the water inlet.



32. DISCONNECT HEATER WATER OUTLET HOSE B


    A155044
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect heater water inlet hose B from the water inlet.



33. DISCONNECT HEATER WATER INLET HOSE B


    A155043
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect heater water outlet hose B from the water outlet.



34. DISCONNECT FUEL TUBE SUB-ASSEMBLY


    A155045
  1. Remove the No. 1 fuel pipe clamp.



    B012941E15
  1. Disconnect the fuel tube from the fuel pipe while pinching part A with your fingers as shown in the illustration.

    NOTICE:
    1. Check for contamination in the pipe and around the connector. Clean if necessary and then disconnect the connector.
    2. Disconnect the connector by hand.
    3. Do not bend, fold or rotate the nylon tube.
    4. If the pipe and connector are stuck together, push and pull the connector until it becomes free.
    5. Put the pipe and connector ends in vinyl bags to prevent damage and contamination.



35. DISCONNECT NO. 1 OIL COOLER INLET HOSE


    A155032
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect the No. 1 oil cooler inlet hose from the No. 1 oil cooler inlet tube.



36. REMOVE NO. 1 OIL COOLER OUTLET HOSE


    A155031
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect the No. 1 oil cooler outlet hose from the No. 1 oil cooler outlet tube.



37. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    D025414E03
  1. Remove the nut from the control shaft lever.

  1. Disconnect the transmission control cable assembly from the control shaft lever.



    C089134E01
  1. Remove the clip and disconnect the transmission control cable assembly from the control cable bracket.



    C090579
  1. Disconnect the control cable from the control cable clamp.



38. DISCONNECT RETURN TUBE SUB-ASSEMBLY


    A163268
  1. Using pliers, grip the claws of the 2 clips and slide the 2 clips to disconnect the 2 return tube sub-assemblies.

  1. Drain the power steering fluid.

    NOTICE:
    Take care not to damage the hose protector.



39. DISCONNECT NO. 1 OIL RESERVOIR TO PUMP HOSE


    A155029
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect the No. 1 oil reservoir to pump hose from the oil reservoir tank.



40. DISCONNECT ENGINE WIRE


    A155037
  1. Disconnect the engine wire from the engine room junction block.

    1. Remove the nut and separate the wire harness.

    2. Using a screwdriver, unlock the engine room junction block. Pull the engine room junction block upward.



    A155030
  1. Remove the bolt and 2 clamps from the body.



    A163267
  1. Remove the 2 bolts and 2 ground cables.

  1. Disconnect the engine wire from the ECM and passenger side junction block.



41. DISCONNECT UNION TO CHECK VALVE HOSE


    A162374
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect the union to check valve hose.



42. REMOVE CENTER EXHAUST PIPE ASSEMBLY (for 4WD)
  1. Remove the center exhaust pipe assembly .



43. REMOVE FRONT EXHAUST PIPE ASSEMBLY (for 4WD)
  1. Remove the front exhaust pipe assembly .



44. REMOVE FRONT EXHAUST PIPE ASSEMBLY (for 2WD)
  1. Remove the front exhaust pipe assembly .



45. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY


    F040503E01
  1. Depress the brake pedal and hold it down.

  1. Using a hexagon wrench (6 mm), loosen the cross groove joint set bolts a half turn.

    HINT:
    Place a cloth in the inside of the universal joint cover so that the boot does not touch the inside of the universal joint cover.



    C092265E01
  1. Put matchmarks on both the flanges.

  1. Remove the 4 nuts, bolts and washers.



    C083005
  1. Remove the 4 bolts, 2 adjusting shims and propeller shaft w/ center bearing shaft assembly.

    NOTICE:
    1. When removing the propeller shaft, do not apply excessive force to the universal joint.
    2. During and after the removal of the propeller shaft, keep the universal joint angle straight (within 15 degrees).
    3. Be careful not to damage the oil seal.



    G024034E01
  1. Insert SST(s) in the transfer extension housing to prevent oil leakage.

    SST
    09325-20010  

    NOTICE:
    Be careful not to damage the oil seal.



46. DISCONNECT FRONT STABILIZER LINK ASSEMBLY LH


    F040136
  1. Remove the nut, and separate the stabilizer link assembly LH.

    HINT:
    If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud.



47. DISCONNECT FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



48. REMOVE FRONT AXLE HUB NUT LH


    F040146E09
  1. Using SST and a hammer, unstake the staked part of the axle hub LH nut.

    SST
    09930-00010  

    NOTICE:
    Loosen the staked part of the nut completely, otherwise the screw of the drive shaft may be damaged.

  1. While applying the brakes, remove the lock axle hub LH nut.



49. REMOVE FRONT AXLE HUB NUT RH

HINT:
Use the same procedures described for the LH side.



50. DISCONNECT FRONT SPEED SENSOR LH


    C083022
  1. Remove the bolt and clip, and separate the sensor wire and hose from the shock absorber.

    NOTICE:
    Be careful not to damage the speed sensor.



    F040147
  1. Remove the bolt, and separate the speed sensor from LH from the steering knuckle.

    NOTICE:
    Prevent foreign matter from adhering to the speed sensor.



51. DISCONNECT FRONT SPEED SENSOR RH

HINT:
Use the same procedures described for the LH side.



52. DISCONNECT TIE ROD ASSEMBLY LH


    F045060E06
  1. Remove the cotter pin and nut.

  1. Using SST, separate the tie rod end from the steering knuckle.

    SST
    09628-62011  



53. DISCONNECT TIE ROD ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



54. SEPARATE FRONT SUSPENSION LOWER NO. 1 ARM LH


    F040142
  1. Remove the bolt and 2 nuts, and separate the No. 1 front suspension arm sub-assembly lower from the lower ball joint.



55. SEPARATE FRONT SUSPENSION LOWER NO. 1 ARM RH

HINT:
Use the same procedures described for the LH side.



56. SEPARATE FRONT AXLE ASSEMBLY LH


    D027403E03
  1. Using a plastic hammer, separate the drive shaft from the axle hub.

    NOTICE:
    Be careful not to damage the boot and speed sensor rotor.



57. SEPARATE FRONT AXLE ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



58. DISCONNECT STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY


59. DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY


    E145264
  1. Remove the bolt and disconnect the discharge hose sub-assembly from the compressor and magnetic clutch.

  1. Remove the O-ring from the discharge hose sub-assembly.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



60. DISCONNECT SUCTION HOSE SUB-ASSEMBLY


    E145265
  1. Remove the bolt and disconnect the suction hose sub-assembly from the compressor and magnetic clutch.

  1. Remove the O-ring from the suction hose sub-assembly.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



61. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
  1. Set the engine lifter.



    A162364
  1. Remove the 6 bolts, 2 nuts, and frame side rail plates RH and LH.



    A162363
  1. Remove the 6 bolts, 2 nuts, and front suspension member brace rear RH and LH.

  1. Operate the engine lifter, then remove the engine assembly from the vehicle.

    NOTICE:
    Make sure that the engine is clear of all wiring and hoses.



62. REMOVE V-RIBBED BELT


    A162386E01
  1. Using SST, release the belt tension by turning the belt tensioner counterclockwise, and remove the V-ribbed belt from the belt tensioner.

    SST
    09249-63010  



    A095070
  1. While turning the belt tensioner counterclockwise, align with its holes, and then insert the 5 mm bi-hexagon wrench into the holes to fix the V-ribbed belt tensioner.



63. REMOVE VANE PUMP ASSEMBLY
  1. Disconnect the power steering oil pressure switch connector.



    A155024
  1. Remove the 2 nuts.



    A139216E01
  1. Loosen the bolt A.

  1. Remove the bolt B.

  1. Remove the bolt A and vane pump assembly.



64. REMOVE FRONT STABILIZER BAR (for 4WD)

HINT:
Click here.



65. REMOVE POWER STEERING LINK
  1. Remove the 2 bolts and power steering link with vane pump.



66. INSTALL ENGINE HANGERS


    A129635E12
  1. Install the 2 engine hangers with the 4 bolts as shown in the illustration.

    Part No.:
    No. 1 Engine hanger 12281-31120
    No. 2 Engine hanger 12282-31100
    Bolts 91671-10825

    Torque:
    33 N*m{ 337 kgf*cm , 24 ft.*lbf }

  1. Attach the engine sling device and hang the engine with the chain block.



67. REMOVE FRONT FRAME ASSEMBLY


    A155022
  1. Disconnect the active mount VSV connector and harness clamp.



    A163266E01
  1. Remove the 2 nuts and disconnect the engine mounting insulators RH and LH.



    A155019
  1. Remove the bolt and disconnect the engine mounting insulator FR.



    A155018
  1. Remove the 2 bolts and separate the engine mounting insulator RR (for 4WD).



68. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH


    F040148E05
  1. Using SST, remove the front drive shaft assembly LH.

    SST
    09520-01010  
    09520-24010   (09520-32040)

    NOTICE:
    1. Be careful not to damage the transaxle case oil seal, inboard joint boot and drive shaft dust cover.
    2. Be careful not to drop the drive shaft assembly.



69. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH (for 2WD)


    C080304
  1. Using a screwdriver, remove the bearing brake hole snap ring.

  1. Remove the bolt and front drive shaft assembly RH from the drive shaft bearing bracket.



70. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH (for 4WD)


    C108268E04
  1. Using SST, remove the front drive shaft assembly RH.

    SST
    09520-01010  
    09520-24010   (09520-32040)

    HINT:
    Overhaul the side following the same procedures as for the LH side.

    NOTICE:
    1. When removing and installing the front drive shaft assembly RH in 4WD vehicle, be sure to first drain all the transaxle oil and transfer oil. If removal and installation is carried out without draining these oils, the transfer oil will flow into the transaxle side. Extensive cleaning will be required if the two oils mix.
    2. Do not damage the oil seal and dust cover.
    3. Move the drive shaft assembly while keeping it level.



71. REMOVE ENGINE WIRE


72. REMOVE STARTER ASSEMBLY


A160251
  1. Disconnect the starter connector.

  1. Open the terminal cap and remove the nut and the starter wire.



    A160252
  1. Remove the 2 bolts and the starter.



73. REMOVE ENGINE FRONT MOUNTING BRACKET


    D030470
  1. Remove the 3 bolts and engine mounting bracket front.



74. REMOVE MANIFOLD STAY


    A155023
  1. Remove the bolt, nut, and manifold stay.



75. REMOVE TRANSFER STIFFENER PLATE RH


    D030512
  1. Remove the 5 bolts and transfer stiffener plate RH.



76. REMOVE AUTOMATIC TRANSAXLE ASSEMBLY (for 2WD)

HINT:
Click here.



77. REMOVE AUTOMATIC TRANSAXLE ASSEMBLY (for 4WD)
Click here


78. REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY


    A129631E01
  1. Using SST, hold the crankshaft.

    SST
    09213-70011   (09213-70020)
    09330-00021  



    A132243
  1. Remove the 8 bolts, front spacer, drive plate and rear spacer.



79. SECURE ENGINE
  1. Secure the engine onto an engine stand with the bolts.



    A129635E12
  1. Remove the engine hangers.



80. REMOVE VENTILATION HOSE


    A162372
  1. Using pliers, grip the claws of the 2 clips and slide the 2 clips to remove the ventilation hose.



81. REMOVE INTAKE AIR SURGE TANK ASSEMBLY


    A162264E01
  1. Disconnect the 2 water by-pass hoses from the throttle with motor body assembly (*1).

  1. Disconnect the vapor feed hose (*2).

  1. Disconnect the throttle with motor body assembly connector and clamp (*3).

  1. Disconnect the No. 1 ventilation hose.



    A162265
  1. Disconnect the connector.

  1. Remove the 4 bolts, No. 1 surge tank stay and throttle body bracket.



    A162266E01
  1. Using a 5 mm socket hexagon wrench, remove the 4 bolts.

  1. Remove the 2 nuts and intake air surge tank (*4).

  1. Remove the gasket from the intake air surge tank (*5).



82. REMOVE IGNITION COIL ASSEMBLY
  1. Remove the 6 bolts and 6 ignition coils.



83. REMOVE NO. 2 ENGINE MOUNTING STAY RH


    A162388
  1. Remove the bolt and No. 2 engine mounting stay RH.



84. REMOVE INTAKE MANIFOLD


    A134933
  1. Uniformly loosen and remove the 6 bolts and 4 nuts.

  1. Remove the intake manifold and 2 gaskets.



85. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH
  1. Disconnect the A/F sensor connector clamp.



    A140781
  1. Uniformly loosen and remove the 6 nuts.

  1. Remove the manifold and gasket.



86. REMOVE OIL LEVEL GAUGE GUIDE SUB-ASSEMBLY


    A155017
  1. Remove the oil level gauge.

  1. Remove the 2 bolts, No. 1 and No. 2 oil level gauge guides.

  1. Remove the O-rings from the oil level gauge guide.



87. REMOVE NO. 2 MANIFOLD STAY


    A140783
  1. Remove the bolt, nut and No. 2 manifold stay.



88. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR


    A140784
  1. Remove the 3 bolts and No. 2 insulator.



89. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH


    A129641
  1. Uniformly loosen and remove the 6 nuts.

  1. Remove the manifold and gasket.



90. REMOVE ENGINE MOUNTING BRACKET RH


    A129642
  1. Remove the engine mounting bracket and 3 bolts.



91. REMOVE DRIVE SHAFT BEARING BRACKET (for 2WD)


    A163583
  1. Remove the 3 bolts and drive shaft bearing bracket.



92. REMOVE ENGINE MOUNTING BRACKET RR (for 4WD)


    A143881
  1. Remove the 3 bolts and engine mounting bracket RR.



93. REMOVE GENERATOR ASSEMBLY


    A162681
  1. Remove the terminal cap.

  1. Remove the nut and disconnect the wire harness from terminal B.

  1. Disconnect the generator connector from the generator assembly.

  1. Disconnect the connector from the compressor and magnetic clutch.

  1. Disconnect the 2 wire harness clamps.



    A162682
  1. Remove the 2 bolts.



    A162683E01
  1. Remove the bolt from the cylinder block.

  1. Disconnect the wire harness clamp and remove the generator assembly.



    A162684
  1. Remove the bolt and wire harness clamp stay.



    A162685
  1. Remove the bolt and bracket.



94. REMOVE COOLER COMPRESSOR ASSEMBLY


95. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


    A129644
  1. Remove the 5 bolts and V-ribbed belt tensioner assembly.



96. REMOVE NO. 2 TIMING GEAR COVER


    A132987
  1. Remove the 2 bolts and No. 2 timing gear cover.



97. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY


    A186537E02
  1. Remove the bolt, 2 plates and No. 2 idler pulley sub-assembly.

    HINT:
    Plate diameter:
    Idler pulley cover plate: 33.6 mm (1.32 in.)
    No. 2 idler pulley cover plate: 37.8 mm (1.49 in.)



98. REMOVE WATER PUMP PULLEY


    A128112E03
  1. Using SST, hold the water pump pulley.

    SST
    09960-10010   (09962-01000, 09963-00700)

  1. Remove the 4 bolts and water pump pulley.



99. REMOVE NO. 1 ENGINE FRONT MOUNTING BRACKET LH


    A129646
  1. Remove the 6 bolts and No. 1 engine front mounting bracket LH.



100. REMOVE RADIO SETTING CONDENSER


    A132991
  1. Remove the 2 bolts and 2 radio setting condensers.



101. REMOVE NO. 1 VACUUM SWITCHING VALVE ASSEMBLY


    A132992
  1. Remove the bolt and No. 1 vacuum switching valve.



102. REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY


    A139194
  1. Using a 24 mm deep socket wrench, remove the engine oil pressure switch assembly.



103. REMOVE KNOCK CONTROL SENSOR


    A129615
  1. Disconnect the 2 knock sensor connectors.

  1. Remove the 2 bolts and then remove the 2 knock control sensors.



104. REMOVE ENGINE COOLANT TEMPERATURE SENSOR


    A129648
  1. Using a 19 mm deep socket wrench, remove the EFI engine coolant temperature sensor and gasket.