Home › ENGINE › 2GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > TERMINALS OF ECM

for Preparation Click here



SFI SYSTEM
*1: The ECM terminal voltage is constant regardless of the output voltage from the sensor.

G035613E37

HINT:
The standard normal voltage between each pair of the ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals are also indicated.
The check results should be compared with the standard normal voltage for that pair of terminals, listed in the "Specified Condition" column.
The illustration above can be used as a reference to identify the ECM terminal locations.


Symbols (Terminal No.)
Wiring Colors
Terminal Descriptions
Conditions
Specified Condition
+B (E4-1) - E1 (E11-1)
B-R - BR
Power source of ECM
Ignition switch ON
9 to 14 V
+B2 (E4-2) - E1 (E11-1)
B-R - BR
Power source of ECM
Ignition switch ON
9 to 14 V
BATT (E4-3) - E1 (E11-1)
B-W - BR
Battery (for measuring the battery voltage and for the ECM memory)
Always
9 to 14 V
VPMP (E4-5) - E1 (E11-1)
W - BR
Vent valve operation signal (built into pump module)
Ignition switch ON
9 to 14 V
MPMP (E4-6) - E1 (E11-1)
G - BR
Vacuum pump operation signal (built into pump module)
Vacuum pump OFF
0 to 3 V
MPMP (E4-6) - E1 (E11-1)
G - BR
Vacuum pump operation signal (built into pump module)
Vacuum pump ON
9 to 14 V
+BM (E4-7) - E1 (E11-1)
R - BR
Power source of ETCS throttle motor
Always
9 to 14 V
MREL (E4-8) - E1 (E11-1)
B-W - BR
EFI relay operation signal
Ignition switch ON
9 to 14 V
IGSW (E4-9) - E1 (E11-1)
B-O - BR
Ignition switch signal
Ignition switch ON
9 to 14 V
FC (E4-10) - E1 (E11-1)
V-G - BR
C/OPEN relay operation signal (fuel pump control)
Ignition switch ON
9 to 14 V
STP (E4-15) - E1 (E11-1)
G-W - BR
Stop light switch signal
Brake pedal depressed
7.5 to 14 V
STP (E4-15) - E1 (E11-1)
G-W - BR
Stop light switch signal
Brake pedal released
Below 1.5 V
ST1- (E4-16) - E1 (E11-1)
LG-R - BR
Stop light switch signal (opposite to STP terminal)
Ignition switch ON, Brake pedal depressed
Below 1.5 V
ST1- (E4-16) - E1 (E11-1)
LG-R - BR
Stop light switch signal (opposite to STP terminal)
Ignition switch ON, Brake pedal released
7.5 to 14 V
VPA (E4-18) - EPA (E4-20)
L-Y - R-B
Accelerator pedal position sensor signal (for engine control)
Ignition switch ON, Accelerator pedal fully released
0.5 to 1.1 V
VPA (E4-18) - EPA (E4-20)
L-Y - R-B
Accelerator pedal position sensor signal (for engine control)
Ignition switch ON, Accelerator pedal fully depressed
2.6 to 4.5 V
VPA2 (E4-19) - EPA2 (E4-21)
W-R - LG
Accelerator pedal position sensor signal (for sensor malfunction detection)
Ignition switch ON, Accelerator pedal fully released
1.2 to 2.0 V
VPA2 (E4-19) - EPA2 (E4-21)
W-R - LG
Accelerator pedal position sensor signal (for sensor malfunction detection)
Ignition switch ON, Accelerator pedal fully depressed
3.4 to 5.0 V
EPA (E4-20) - VPA (E4-18)
R-B - L-Y
Accelerator pedal position sensor signal (for engine control)
Ignition switch ON, Accelerator pedal fully released
0.5 to 1.1 V
EPA (E4-20) - VPA (E4-18)
R-B - L-Y
Accelerator pedal position sensor signal (for engine control)
Ignition switch ON, Accelerator pedal fully depressed
2.6 to 4.5 V
EPA2 (E4-21) - VPA2 (E4-19)
LG - W-R
Accelerator pedal position sensor signal (for sensor malfunction detection)
Ignition switch ON, Accelerator pedal fully released
1.2 to 2.0 V
EPA2 (E4-21) - VPA2 (E4-19)
LG - W-R
Accelerator pedal position sensor signal (for sensor malfunction detection)
Ignition switch ON, Accelerator pedal fully depressed
3.4 to 5.0 V
PPMP (E4-22) - E2 (E9-28)
B - BR
Pressure sensor signal (built into pump module)
Ignition switch ON
3 to 3.6 V
TC (E4-23) - E1 (E11-1)
P-B - BR
Terminal TC of DLC3
Ignition switch ON
9 to 14 V
VCPA (E4-26) - EPA (E4-20)
GR-R - R-B
Power source of accelerator pedal position sensor (for VPA)
Ignition switch ON
4.5 to 5.0 V
VCP2 (E4-27) - EPA2 (E4-21)
B-R - LG
Power source of accelerator pedal position sensor (for VPA2)
Ignition switch ON
4.5 to 5.0 V
TACH (E5-1) - E1 (E11-1)
B-O - BR
Engine speed signal (for combination meter)
Idling
Pulse generation
(see waveform 11)
SPD (E5-8) - E1 (E11-1)
V-W - BR
Vehicle speed signal from combination meter
Ignition switch ON, driving wheel rotated slowly
Pulse generation
(see waveform 8)
W (E5-30) - E1 (E11-1)
B-Y - BR
Malfunction Indicator Lamp (MIL) operation signal
Ignition switch ON
Below 3.0 V
W (E5-30) - E1 (E11-1)
B-Y - BR
Malfunction Indicator Lamp (MIL) operation signal
Idling
9 to 14 V
CANH (E5-33) - CANL (E5-34)
B - W
CAN communication circuit
Ignition switch off
54 to 69 Ω
CANL (E5-34) - CANH (E5-33)
W - B
CAN communication circuit
Ignition switch off
54 to 69 Ω
E1 (E11-1) - Body ground
BR - -
Earth (ground) circuit of ECM
Always
Below 1 V
#10 (E11-2) - E01 (E9-7)
#20 (E11-3) - E01 (E9-7)
#30 (E11-4) - E01 (E9-7)
#40 (E11-5) - E01 (E9-7)
#50 (E11-6) - E01 (E9-7)
#60 (E11-7) - E01 (E9-7)
L - W-B
R - W-B
B - W-B
W - W-B
B-W - W-B
G - W-B
Fuel injector operation signal
Ignition switch ON
9 to 14 V
#10 (E11-2) - E01 (E9-7)
#20 (E11-3) - E01 (E9-7)
#30 (E11-4) - E01 (E9-7)
#40 (E11-5) - E01 (E9-7)
#50 (E11-6) - E01 (E9-7)
#60 (E11-7) - E01 (E9-7)
L - W-B
R - W-B
B - W-B
W - W-B
B-W - W-B
G - W-B
Fuel injector operation signal
Idling
Pulse generation
(see waveform 3)
PSW (E11-10) - E1 (E11-1)
R-W - BR
P/S pressure switch signal
Ignition switch ON
9 to 14 V
NSW (E10-8) - E1 (E11-1)
B-Y - BR
Park/Neutral position switch signal
Ignition switch ON, Shift lever position P or N
9 to 14 V
NSW (E10-8) - E1 (E11-1)
B-Y - BR
Park/Neutral position switch signal
Ignition switch ON, Shift lever position other than P or N
9 to 14 V
STA (E11-11) - E1 (E11-1)
B-L - BR
Starter relay operation signal
Cranking
9 to 14 V
OC2- (E11-14) - OC2+ (E11-15)
G-B - L-R
Camshaft timing Oil Control Valve (OCV) operation signal (Intake side)
Ignition switch ON
Pulse generation
(see waveform 1)
OE2+ (E11-27) - OE2- (E11-32)
W - G-R
Camshaft timing Oil Control Valve (OCV) operation signal (Intake side)
Ignition switch ON
Pulse generation
(see waveform 1)
OC1- (E11-16) - OC1+ (E11-17)
G-R - G-W
Camshaft timing Oil Control Valve (OCV) operation signal (Intake side)
Ignition switch ON
Pulse generation
(see waveform 1)
OE1+ (E11-26) - OE1- (E11-31)
G - R
Camshaft timing Oil Control Valve (OCV) operation signal (Intake side)
Ignition switch ON
Pulse generation
(see waveform 1)
VV2+ (E11-18) - VV2- (E11-28)
V - G
Variable Valve Timing (VVT) sensor signal (Intake side)
Idling
Pulse generation
(see waveform 5)
VV1+ (E11-19) - VV1- (E11-29)
B-W - L-Y
Variable Valve Timing (VVT) sensor signal (Intake side)
Idling
Pulse generation
(see waveform 5)
NE- (E11-20) - NE+ (E11-21)
B - W
Crankshaft position sensor signal
Idling
Pulse generation
(see waveform 5)
NE+ (E11-21) - NE- (E11-20)
W - B
Crankshaft position sensor signal
Idling
Pulse generation
(see waveform 5)
EV2- (E11-22) - EV2+ (E11-23)
R - P
Variable Valve Timing (VVT) sensor signal (Exhaust side)
Idling
Pulse generation
(see waveform 5)
EV2+ (E11-23) - EV2- (E11-22)
P - R
Variable Valve Timing (VVT) sensor signal (Exhaust side)
Idling
Pulse generation
(see waveform 5)
EV1- (E11-24) - EV1+ (E11-25)
L-W - B-W
Variable Valve Timing (VVT) sensor signal (Exhaust side)
Idling
Pulse generation
(see waveform 5)
EV1+ (E11-25) - EV1- (E11-24)
B-W - L-W
Variable Valve Timing (VVT) sensor signal (Exhaust side)
Idling
Pulse generation
(see waveform 5)
VV2- (E11-28) - VV2+ (E11-18)
G - V
Variable Valve Timing (VVT) sensor signal (Intake side)
Idling
Pulse generation
(see waveform 5)
VV1- (E11-29) - VV1+ (E11-19)
L-Y - B-W
Variable Valve Timing (VVT) sensor signal (Intake side)
Idling
Pulse generation
(see waveform 5)
HT1B (E9-1) - E1 (E11-1)
HT2B (E10-5) - E1 (E11-1)
L - BR
W-L - BR
Heated oxygen sensor heater operation signal
Idling
Below 3.0 V
HT1B (E9-1) - E1 (E11-1)
HT2B (E10-5) - E1 (E11-1)
L - BR
W-L - BR
Heated oxygen sensor heater operation signal
Ignition switch ON
9 to 14 V
ACM (E9-3) - E1 (E11-1)
R - BR
VSV for active control mount system operation signal
Ignition switch ON
9 to 14 V
M- (E9-4) - ME01 (E10-3)
W - W-B
Throttle drive motor operation signal (negative terminal)
Idling with warm engine
Pulse generation
(see waveform 10)
M+ (E9-5) - ME01 (E10-3)
B - W-B
Throttle drive motor operation signal (positive terminal)
Idling with warm engine
Pluse generation
(see waveform 9)
E02 (E9-6) - Body ground
W-B - -
Earth (ground) circuit of ECM
Always
Below 1 V
E01 (E9-7) - Body ground
W-B - -
Earth (ground) circuit of ECM
Always
Below 1 V
IGT1 (E9-8) - E1 (E11-1)
IGT2 (E9-9) - E1 (E11-1)
IGT3 (E9-10) - E1 (E11-1)
IGT4 (E9-11) - E1 (E11-1)
IGT5 (E9-12) - E1 (E11-1)
IGT6 (E9-13) - E1 (E11-1)
R-L - BR
P - BR
Y-B - BR
L-Y - BR
G-Y - BR
L-R - BR
Ignition coil with igniter (ignition signal)
Idling
Pulse generation
(see waveform 6)
GE01 (E9-17) - E1 (E11-1)
- - BR
Shielded earth (ground) circuit of throttle drive motor
Always
Below 1 V
OX1B (E9-18) - E2 (E9-28)
OX2B (E10-33) - E2 (E9-28)
W - BR
B - BR
Heated oxygen sensor signal
With engine speed at 2500 rpm for 2 minutes after warming up
Pulse generation
(see waveform 2)
VTA2 (E9-19) - E2 (E9-28)
B-R - BR
Throttle position sensor signal (for sensor malfunction detection)
Ignition switch ON, Accelerator pedal fully released
2.1 to 3.1 V
VTA2 (E9-19) - E2 (E9-28)
B-R - BR
Throttle position sensor signal (for sensor malfunction detection)
Ignition switch ON, Accelerator pedal fully depressed
4.5 to 5.0 V
VTA1 (E9-20) - E2 (E9-28)
LG - BR
Throttle position sensor signal (for engine control)
Ignition switch ON, Throttle valve fully closed
0.5 to 1.2 V
VTA1 (E9-20) - E2 (E9-28)
LG - BR
Throttle position sensor signal (for engine control)
Ignition switch ON, Throttle valve fully open
3.2 to 4.8 V
THW (E9-21) - E2 (E9-28)
G-B - BR
Engine coolant temperature sensor signal
Idling, Engine coolant temperature 80°C (176°F)
0.2 to 1.0 V
THA (E9-22) - E2 (E9-28)
L-B - BR
Intake air temperature sensor signal
Idling, Intake air temperature 20°C (68°F)
0.5 to 3.4 V
VC (E9-23) - E2 (E9-28)
Y - BR
Power source of sensors (specific voltage)
Ignition switch ON
4.5 to 5.0 V
IGF1 (E9-24) - E1 (E11-1)
W-R - BR
Ignition coil with igniter (ignition confirmation signal)
Ignition switch ON
4.5 to 5.0 V
IGF1 (E9-24) - E1 (E11-1)
W-R - BR
Ignition coil with igniter (ignition confirmation signal)
Idling
Pulse generation
(see waveform 6)
AICV (E9-27) - E1 (E11-1)
W - BR
VSV for Air intake control system operation signal
Ignition switch ON
9 to 14 V
E2 (E9-28) - E1 (E11-1)
BR - BR
Earth (ground) circuit of sensors for ETCS
Always
Below 1 V
E2G (E9-29) - E1 (E11-1)
L-W - BR
Earth (ground) circuit of sensor for mass air flow meter
Always
Below 1 V
VG (E9-30) - E2G (E9-29)
R - L-W
Mass Air Flow (MAF) meter signal
Idling, Shift lever position P or N, A/C switch OFF
0.5 to 3.0 V
ACIS (E9-33) - E1 (E11-1)
R-Y - BR
VSV for ACIS (Acoustic Control Induction System) operation signal
Ignition switch ON
9 to 14 V
PRG (E9-34) - E1 (E11-1)
G - BR
Purge VSV for EVAP system operation signal
Ignition switch ON
9 to 14 V
PRG (E9-34) - E1 (E11-1)
G - BR
Purge VSV for EVAP system operation signal
Idling
Pulse generation
(see waveform 7)
HA2A (E10-1) - E05 (E10-6)
Y - W-B
A/F sensor heater operation signal
Idling
Below 3.0 V
HA2A (E10-1) - E05 (E10-6)
Y - W-B
A/F sensor heater operation signal
Ignition switch ON
9 to 14 V
HA1A (E10-2) - E04 (E10-7)
B-W - W-B
A/F sensor heater operation signal
Idling
Below 3.0 V
HA1A (E10-2) - E04 (E10-7)
B-W - W-B
A/F sensor heater operation signal
Ignition switch ON
9 to 14 V
ME01 (E10-3) - E1 (E11-1)
W-B - BR
Earth (ground) circuit of ECM
Always
Below 1 V
E03 (E10-4) - E1 (E11-1)
W-B - BR
Earth (ground) circuit of ECM
Always
Below 1 V
HT2B (E10-5) - E1 (E11-1)
HT1B (E9-1) - E1 (E11-1)
W-L - BR
L - BR
Heated oxygen sensor heater operation signal
Idling
Below 3.0 V
HT2B (E10-5) - E1 (E11-1)
HT1B (E9-1) - E1 (E11-1)
W-L - BR
L - BR
Heated oxygen sensor heater operation signal
Ignition switch ON
9 to 14 V
E05 (E10-6) - E1 (E11-1)
W-B - BR
Earth (ground) circuit of ECM
Always
Below 1 V
E04 (E10-7) - E1 (E11-1)
W-B - BR
Earth (ground) circuit of ECM
Always
Below 1 V
EKN2 (E10-20) - KNK2 (E10-21)
G - R
Earth (ground) circuit of knock sensor
With engine speed at 4000 rpm after warming up engine
Pulse generation
(see waveform 4)
KNK2 (E10-21) - EKN2 (E10-20)
R - G
Knock sensor signal
With engine speed at 4000 rpm after warming up engine
Pulse generation
(see waveform 4)
A1A+ (E10-22) - E1 (E11-1)
BR - BR
A/F sensor signal
Ignition switch ON
3.3 V*1
A1A+ (E10-22) - E1 (E11-1)
BR - BR
A/F sensor signal
Ignition switch ON
3.0 V*1
A2A+ (E10-23) - E1 (E11-1)
P - BR
A/F sensor signal
Ignition switch ON
3.3 V*1
A2A+ (E10-23) - E1 (E11-1)
P - BR
A/F sensor signal
Ignition switch ON
3.0 V*1
EKNK (E10-28) - KNK1 (E10-29)
W - B
Earth (ground) circuit of knock sensor
With engine speed at 4000 rpm after warming up
Pulse generation
(see waveform 4)
KNK1 (E10-29) - EKNK (E10-28)
B - W
Knock sensor signal
With engine speed at 4000 rpm after warming up
Pulse generation
(see waveform 4)
A1A- (E10-30) - E1 (E11-1)
Y - BR
A/F sensor
Ignition switch ON
3.3 V*1
A1A- (E10-30) - E1 (E11-1)
Y - BR
A/F sensor
Ignition switch ON
3.0 V*1
A2A- (E10-31) - E1 (E11-1)
L - BR
A/F sensor
Ignition switch ON
3.3 V*1
A2A- (E10-31) - E1 (E11-1)
L - BR
A/F sensor
Ignition switch ON
3.0 V*1
OX2B (E10-33) - E2 (E9-28)
OX1B (E9-18) - E2 (E9-28)
B - BR
W - BR
Heated oxygen sensor signal
With engine speed at 2500 rpm for 2 minutes after warming up
Pulse generation
(see waveform 2)


    A093229E14
  1. WAVEFORM 1

    1. Camshaft Timing Oil Control Valve (OCV) operation signal
      ECM Terminal Names
      Between OC1+ and OC1- , OC2+ and OC2- , OE1+ and OE1- , or OE2+ and OE2-
      Tester Ranges
      5 V/DIV, 1 msec./DIV
      Conditions
      Idling

      HINT:
      The wavelength becomes shorter as the engine rpm increases.



  2. A088863E16
  3. WAVEFORM 2

    1. Heated oxygen sensor signal
      ECM Terminal Names
      Between OX1B and E2, or OX2B and E2
      Tester Ranges
      0.2 V/DIV, 200 msec./DIV
      Conditions
      Engine speed is maintained at 2500 rpm for 2 minutes after sensor is warmed up

      HINT:
      In the Data List, item O2S B1S2 shows the ECM input values from the heated oxygen sensor.



  4. G035622E04
  5. WAVEFORM 3

    1. Fuel injector operation signal
      ECM Terminal Names
      Between #10 (to 60) and E01
      Tester Ranges
      30 V/DIV, 20 msec./DIV
      Conditions
      Idling

      HINT:
      The wavelength becomes shorter as the engine rpm increases.



  6. A085286E30
  7. WAVEFORM 4

    1. Knock sensor signal
      ECM Terminal Names
      Between KNK1 and EKNK, or KNK2 and EKN2
      Tester Ranges
      0.01 to 10 V/DIV, 0.01 to 10 msec./DIV
      Conditions
      Engine speed is maintained at 4000 rpm after engine is warmed up

      HINT:
      1. The wavelength becomes shorter as the engine rpm increases.
      2. The waveforms and amplitudes displayed differ slightly depending on the vehicle.



  8. A122768E07
  9. WAVEFORM 5

    1. Variable Valve Timing (VVT) sensor signal (1)

    2. Crankshaft position sensor signal (2)
      ECM Terminal Names
      (1) EV1+ and EV1-, or EV2+ and EV2-
      (2) Between NE+ and NE-
      Tester Ranges
      5 V/DIV, 20 ms./DIV
      Conditions
      Idling

      HINT:
      The wavelength becomes shorter as the engine rpm increases.



  10. A122767E10
  11. WAVEFORM 6

    1. Variable Valve Timing (VVT) sensor signal (1)

    2. Crankshaft position sensor signal (2)
      ECM Terminal Names
      (1) Between VV1+ and VV1- , VV2+ and VV2-
      (2) Between NE+ and NE-
      Tester Ranges
      5 V/DIV, 20 ms./DIV
      Conditions
      Idling

      HINT:
      The wavelength becomes shorter as the engine rpm increases.



  12. G035664E06
  13. WAVEFORM 7

    1. Igniter IGT signal (from ECM to igniter) (1)

    2. Igniter IGF signal (from igniter to ECM) (2)
      ECM Terminal Names
      (1) Between IGT (1 to 6) and E1
      (2) Between IGF1 and E1
      Tester Ranges
      2 V/DIV, 20 msec./DIV
      Conditions
      Idling

      HINT:
      The wavelength becomes shorter as the engine rpm increases.



  14. G042964E01
  15. WAVEFORM 8

    1. Purge VSV for EVAP system operation signal
      ECM Terminal Names
      Between PRG and E1
      Tester Ranges
      10 V/DIV, 50 msec./DIV
      Conditions
      Idling

      HINT:
      If the waveform is not similar to that shown in the illustration, check the waveform again after idling for 10 minutes or more.



  16. A093224E14
  17. WAVEFORM 9

    1. Vehicle speed signal
      ECM Terminal Names
      Between SPD and E1
      Tester Ranges
      2 V/DIV, 20 msec./DIV
      Conditions
      Driving at 12 mph (20 km/h)

      HINT:
      1. The wavelength becomes shorter as the vehicle speed increases.
      2. Depending on the vehicle, the output waveform voltage may rise to 12 V if influenced by optionally installed systems.



  18. A093274E16
  19. WAVEFORM 10

    1. Throttle drive motor operation signal (positive terminal)
      ECM Terminal Names
      Between M+ and ME01
      Tester Ranges
      5 V/DIV, 1 msec./DIV
      Conditions
      Idling with warm engine

      HINT:
      The duty ratio varies depending on the throttle actuator operation.



  20. A093275E15
  21. WAVEFORM 11

    1. Throttle drive motor operation signal (negative terminal)
      ECM Terminal Names
      Between M- and ME01
      Tester Ranges
      5 V/DIV, 1 msec./DIV
      Conditions
      Idling with warm engine

      HINT:
      The duty ratio varies depending on the throttle actuator operation.



  22. A093225E12
  23. WAVEFORM 12

    1. Engine speed signal
      ECM Terminal Names
      Between TACH and E1
      Tester Ranges
      5 V/DIV, 10 msec./DIV
      Conditions
      Idling

      HINT:
      The wavelength becomes shorter as the engine rpm increases.