SFI SYSTEM > DIAGNOSIS SYSTEM |
| DESCRIPTION |
When troubleshooting OBD II (On-Board Diagnostics) vehicles, the Techstream (complying with SAE J1987) must be connected to the DLC3 (Data Link Connector 3) of the vehicle. Various data in the vehicle's ECM (Engine Control Module) can be then read.
![]() |
OBD II regulations require that the vehicle's on-board computer illuminates the MIL (Malfunction Indicator Lamp) on the instrument panel when the computer detects a malfunction in:
The emission control system and components
The powertrain control components (which affect vehicle emissions)
The computer itself
In addition, the applicable DTCs (Diagnostic Trouble Codes) prescribed by SAE J2012 are recorded on 3 consecutive trips, the MIL turns off automatically but the DTCs remain recorded in the ECM memory.
![]() |
To check for DTCs, connect the Techstream to the DLC3. The tester displays DTCs, freeze frame data, and a variety of engine data. The DTCs and freeze frame data can be erased with the tester (Click here).
In order to enhance OBD function on vehicles and develop the Off-Board diagnosis system, CAN communication is introduced in this system (CAN: Controller Area Network). It minimizes a gap between technician skills and vehicle technology. CAN is a network, which uses a pair of data transmission lines, spanning multiple computers and sensors. It allows a high speed communication between the systems and to simplify the wire harness connection.
Since this system is equipped with the CAN communication, connecting the Techstream is necessary to display any information from the ECM. (Also the communication between the Techstream and the ECM uses CAN communication signal).
| NORMAL MODE AND CHECK MODE |
The diagnosis system operates in normal mode during normal vehicle use. In normal mode, 2 trip detection logic is used to ensure accurate detection of malfunctions. Check mode is also available as an option for technicians. In check mode, 1 trip detection logic is used for simulating malfunction symptoms and increasing the system's ability to detect malfunctions, including intermittent problems (the Techstream only) (Click here).
| 2 TRIP DETECTION LOGIC |
When a malfunction is first detected, the malfunction is temporarily stored in the ECM memory (1st trip). If the same malfunction is detected during the next subsequent drive cycle, the MIL illuminates (2nd trip).
| FREEZE FRAME DATA |
The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
| DLC3 (Data Link Connector 3) |
![]() |
The vehicle's ECM uses ISO 15765-4 for communication protocol. The terminal arrangement of the DLC3 complies with SAE J1962 and matches the ISO 15765-4 format.
| Symbols | Terminal No. | Names | Reference terminals | Results | Conditions |
| SIL | 7 | Bus "+" line | 5 - Signal ground | Pulse generation | During transmission |
| CG | 4 | Chassis ground | Body ground | Below 1 Ω | Always |
| SG | 5 | Signal ground | Body ground | Below 1 Ω | Always |
| BAT | 16 | Battery positive | Body ground | 10 to 14 V | Always |
| CANH | 6 | CAN "High" line | 14 - CANL | 54 to 69 Ω | Ignition switch off*
|
| CANH | 6 | CAN "High" line | Battery positive | 200 Ω or more | Ignition switch off*
|
| CANH | 6 | CAN "High" line | 4 - CG | 200 Ω or more | Ignition switch off*
|
| CANL | 14 | CAN "Low" line | Battery positive | 6 kΩ or higher | Ignition switch off*
|
| CANL | 14 | CAN "Low" line | 4 - CG | 6 kΩ or higher | Ignition switch off*
|
| BATTERY VOLTAGE |
| MIL (Malfunction Indicator Lamp) |
The MIL is illuminated when the ignition switch is first turned to the ON position (the engine is not running).
The MIL should turn off when the engine is started. If the MIL remains illuminated, the diagnosis system has detected a malfunction or abnormality in the system.
| ALL READINESS |
Connect the Techstream to the DLC3.
Turn the ignition switch to the ON position.
Turn the Techstream ON.
Clear the DTCs (Click here).
Perform the DTC judgment driving pattern to run the DTC judgment.
Select the following menu items: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTCs to be confirmed.
Check the DTC judgment result.
| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| UNKNOWN |
|