Home › ENGINE › 2GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > FREEZE FRAME DATA

for Preparation Click here



DESCRIPTION
  1. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

    HINT:
    If it is impossible to duplicate the problem even though a DTC is detected, confirm the freeze frame data.



  2. G038619
  3. The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using the Techstream, five separate sets of freeze frame data, including the data values at the time when the DTC was set, can be checked.

    1. 3 data sets before the DTC was set
    2. 1 data set when the DTC was set
    3. 1 data set after the DTC was set
    These data sets can be used to simulate the condition of the vehicle around the time of the occurrence of the malfunction. The data may assist in identifying of the cause of the malfunction, and in judging whether it was temporary or not.


LIST OF FREEZE FRAME DATA
*1: Only for Mexico models

LABEL
(Techstream Display)
Measurement Item
Diagnostic Note
Trouble Code
Freeze DTC
-
Vehicle Speed
Vehicle speed
Speed indicated on speedometer
Engine Speed
Engine speed
-
Calculate Load
Calculate load
Calculated load by ECM
Vehicle Load
Vehicle load
-
MAF
Mass air flow volume
If value is approximately 0.0 g/s:
  1. Mass air flow meter power source circuit open or shorted
  2. VG circuit open or shorted
If value is 160.0 g/s or more:
  1. E2G circuit open
Atmosphere Pressure
Atmospheric pressure
-
Coolant Temp
Engine coolant temperature
If value is -40°C (-40°F), sensor circuit open
If value is 140°C (284°F), sensor circuit shorted
Intake Air
Intake air temperature
If value is -40°C (-40°F), sensor circuit open
If value is 140°C (284°F), sensor circuit shorted
Engine Run Time
Accumulated engine running time
-
Initial Engine Coolant Temp
Initial engine coolant temperature
-
Initial Intake Air Temp
Initial intake air temperature
-
Battery Voltage
Battery voltage
-
Accel Sens. No. 1 Volt %
Absolute Accelerator Pedal Position (APP) No. 1
-
Accel Sens. No. 2 Volt %
Absolute APP No. 2
-
Throttle Sensor Volt %
Throttle position
Read value with ignition switch on (Do not start engine)
Throttle Sensor #2 Volt %
Throttle sensor positioning #2
Read value with ignition switch on (Do not start engine)
Throttle Sensor Position
Throttle sensor positioning
Read value with ignition switch on (Do not start engine)
Throttle Motor Duty
Throttle motor
-
Injector (Port)
Injector
-
Injector Volume (Cylinder 1)
Injection volume
-
Fuel Pump Speed Control
Fuel pump speed control status
-
Fuel Pump/Speed Status
Fuel pump speed status
VSV for EVAP controlled by ECM (ground side duty control)
Vacuum Pump
Key-off EVAP system pump status
-
EVAP (Purge) VSV
EVAP purge VSV duty ratio
-
Evap Purge Flow
Purge flow
-
Purge Density Learn Value
Learning value of purge density
-
EVAP System Vent Valve
Key-off EVAP system vent valve status
-
Tank Bypass VSV*1
Tank bypass VSV
-
Canister Control VSV*1
Canister control VSV
-
EVAP Purge VSV
EVAP purge VSV
-
Target Air-Fuel Ratio
Air-fuel ratio
-
AF Lambda B1 S1
Fuel trim at A/F sensor
-
AF Lambda B2 S1
Fuel trim at A/F sensor
-
AFS Voltage B1 S1
A/F sensor output
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check voltage output of sensor
AFS Voltage B2 S1
A/F sensor output
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check voltage output of sensor
AFS Current B1S1
Air fuel ratio sensor current
-
AFS Current B2S1
Air fuel ratio sensor current
-
O2S B1 S2
Heated oxygen sensor output
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check voltage output of sensor
O2S B2 S2
Heated oxygen sensor output
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check voltage output of sensor
O2S Impedance B1 S2
Heated oxygen sensor impedance (Sensor 2)
-
O2S Impedance B2 S2
Heated oxygen sensor impedance (Sensor 2)
-
Short FT #1
Short-term fuel trim of bank 1
Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
Long FT #1
Long-term fuel trim of bank 1
Overall fuel compensation carried out in long-term to compensate for a continual deviation of short-term fuel trim from central valve
Total FT #1
Total fuel trim of bank 1
-
Short FT #2
Short-term fuel trim of bank 2
Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio
Long FT #2
Long-term fuel trim of bank 2
Overall fuel compensation carried out in long-term to compensate for a continual deviation of short-term fuel trim from central valve
Total FT #2
Total fuel trim of bank 2
-
Fuel System Status #1
Fuel system status (bank 1)
  1. OL (Open Loop): Has not yet satisfied conditions to go closed loop
  2. CL (Closed Loop): Using air fuel ratio sensor as feedback for fuel control
  3. OLDRIVE: Open loop due to driving conditions (fuel enrichment)
  4. OLFAULT: Open loop due to detected system fault
  5. CLFAULT: Closed loop but air fuel ratio sensor, which used for fuel control malfunctioning
Fuel System Status #2
Fuel system status (bank 2)
  1. OL (Open Loop): Has not yet satisfied conditions to go closed loop
  2. CL (Closed Loop): Using air fuel ratio sensor as feedback for fuel control
  3. OLDRIVE: Open loop due to driving conditions (fuel enrichment)
  4. OLFAULT: Open loop due to detected system fault
  5. CLFAULT: Closed loop but air fuel ratio sensor, which used for fuel control malfunctioning
IGN Advance
Ignition advance
-
Knock Feedback Value
Feedback value of knocking
-
Knock Correct Learn Value
Correction learning value of knocking
-
ACIS VSV
VSV for Acoustic control induction system
-
AICV VSV
VSV for Air Intake Control Induction System (AICS)
-
VVT Control Status #1
VVT control (bank 1) status ON or OFF
Active test support data
VVT Control Status #2
VVT control (bank 2 Intake side) status
-
VVT Aim Angle #1
VVT aim angle
-
VVT Change Angle #1
VVT change angle
-
VVT OCV Duty #1
VVT OCV operation duty
-
VVT Aim Angle #2
VVT aim angle (bank 2 Intake side)
-
VVT Change Angle #2
VVT change angle (bank 2 Intake side)
-
VVT OCV Duty #2
VVT OCV (bank 2 Intake side) operation duty
-
VVT Ex Hold Lrn Val #1
VVT exhaust hold duty ratio learning value (bank 1 Exhaust side)
-
VVT Ex Chg Angle #1
VVT change angle (bank 1 Exhaust side)
-
VVT Ex OCV Duty #1
VVT OCV (bank 1 Exhaust side) operation duty
-
VVT Ex Hold Lrn Val #2
VVT exhaust hold duty ratio learning value (bank 2 Exhaust side)
-
VVT Ex Chg Angle #2
VVT change angle (bank 2 Exhaust side)
-
VVT Ex OCV Duty #2
VVT OCV (bank 2 Exhaust side) operation duty
-
Catalyst Temp B1 S1
Catalyst temperature
-
Catalyst Temp B2 S1
Catalyst temperature
-
Catalyst Temp B1 S2
Catalyst temperature
-
Catalyst Temp B2 S2
Catalyst temperature
-
Starter Signal
Starter signal
-
Starter Control
Starter switch status
-
Power Steering Signal Record
Power steering signal (history)
-
Starter Relay
Starter relay status
-
Power Steer. Sig. Record
Power steering signal (history)
This signal status usually ON until ignition switch turned off
ACC Relay
ACC relay status
-
Neutral Position SW Signal
Park/neutral position switch status ON or OFF
-
Stop Light Switch
Stop light switch
-
A/C Signal
A/C signal
-
Close Throttle Position SW
Closed throttle position switch
-
Electrical Load Signal
Electrical load signal
-
Time after DTC Cleared
Cumulative time after DTC cleared
-
Distance from DTC Cleared
Accumulated distance after DTC cleared
-
Warmup Cycle Cleared DTC
Warm-up cycle after DTC cleared
-
TC and TE1
TC and TE1 terminals of DLC3
-
Ignition Trig. Count
Ignition
-
Cylinder #1 Misfire Count
Cylinder #1 misfire rate
Displayed only during idling
Cylinder #2 Misfire Count
Cylinder #2 misfire rate
Displayed only during idling
Cylinder #3 Misfire Count
Cylinder #3 misfire rate
Displayed only during idling
Cylinder #4 Misfire Count
Cylinder #4 misfire rate
Displayed only during idling
Cylinder #5 Misfire Count
Cylinder #5 misfire rate
Displayed only during idling
Cylinder #6 Misfire Count
Cylinder #6 misfire rate
Displayed only during idling
All Cylinders Misfire Count
All cylinder misfire rate
Displayed only during idling
Misfire RPM
Misfire RPM
-
Misfire Load
Misfire load
-
Misfire Margin
Misfire monitoring
-
Catalyst OT MF F/C
Catalyst over temperature Misfire prevention fuel cut
-
Cat OT MF F/C History
Catalyst over temperature Misfire prevention fuel cut history
-
Cat OT MF F/C Cylinder#1
Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#2
Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#3
Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#4
Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#5
Display of fuel cut operation in No. 5 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#6
Display of fuel cut operation in No. 6 cylinder (if certain level of misfire malfunction is detected)
-
ACM
ACM control status
-
Electric Fan Motor
Electric fan motor
-
Idle Fuel Cut
Idle fuel cut
ON: when throttle valve fully closed and engine speed over 1500 rpm
FC TAU
FC TAU
Fuel cut initiated under light load to prevent incomplete combustion