Home › ENGINE › 2GR-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2119    Throttle Actuator Control Throttle Body Range / Performance

for Preparation Click here


DESCRIPTION

The Electronic Throttle Control System (ETCS) is composed of the throttle actuator, Throttle Position (TP) sensor, Accelerator Pedal Position (APP) sensor, and ECM. The ECM operates the throttle actuator to regulate the throttle valve in response to driver inputs. The TP sensor detects the opening angle of the throttle valve, and provides the ECM with feedback so that the throttle valve can be appropriately controlled by the ECM.

DTC No.
DTC Detection Condition
Trouble Area
P2119
Throttle valve opening angle continues to vary greatly from target opening angle (1 trip detection logic)
  1. ETCS
  2. ECM

MONITOR DESCRIPTION

The ECM determines the actual opening angle of the throttle valve from the TP sensor signal. The actual opening angle is compared to the target opening angle commanded by the ECM. If the difference between these two values is outside the standard range, the ECM interprets this as a malfunction in the ETCS. The ECM then illuminates the MIL and sets the DTC.
If the malfunction is not repaired successfully, the DTC is set when the accelerator pedal is quickly released (to close the throttle valve) after the engine speed reaches 5000 rpm by the accelerator pedal being fully depressed (fully open the throttle valve).

MONITOR STRATEGY


Related DTCs
P2119: ETCS malfunction
Required Sensors / Components (Main)
Throttle actuator
Required Sensors / Components (Related)
-
Frequency of Operation
Continuous
Duration
1 second
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever these DTCs are not present
None
System guard*
ON
*System guard set when the following conditions are met
-
Throttle actuator
ON
Throttle actuator duty calculation
Executing
Throttle position sensor
Fail determined
Throttle actuator current-cut
Not executing
Throttle actuator power supply
4 V or more
Throttle actuator
Fail determined

TYPICAL MALFUNCTION THRESHOLDS


Either of following conditions is met
Condition A or B
A. Commanded closed TP - current closed TP
0.3 V or more
B. Commanded open TP - current open TP
0.3 V or more

FAIL-SAFE

When this DTC, as well as other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions, is set, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator off, and the throttle valve is returned to a 6° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed slowly, the vehicle can be driven slowly.
Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

Refer to DTC P2102 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2119)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Trouble Code.

  1. Read the DTCs.

    Result:

    Display (DTC Output)
    Proceed to
    P2119
    A
    P2119 and other DTCs
    B

    HINT:
    If any DTCs other than P2119 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.CHECK WHETHER DTC OUTPUT RECURS (DTC P2119)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Allow the engine to idle for 15 seconds.

    CAUTION:
    Perform the procedures "A" and "B" below with great care. Failure to do so may result in the vehicle unexpectedly rolling away.

  1. Securely apply the parking brake and move the gear selector lever to the D position (Procedure "A").

  1. While depressing the brake pedal securely, fully depress the accelerator pedal for 5 seconds (Procedure "B").

  1. Select the following menu items on the tester: Powertrain / Engine and ECT / Trouble Code.

  1. Read the DTCs.

    HINT:
    The voltage output of the throttle position sensor can be checked during procedure "B" using the Techstream. Variations in the voltage output indicate that the throttle actuator is in operation. To check the voltage output using the Techstream, select the following menu items: Powertrain / Engine and ECT / Data List / Throttle Position No. 1.

    OK:
    No DTC output.



NG
REPLACE THROTTLE BODY (Click here)
OK

CHECK FOR INTERMITTENT PROBLEMS