Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

DTC    B1422/22    Compressor Lock Sensor Circuit

for Preparation Click here


SYSTEM DESCRIPTION

The ECM sends an engine speed signal to the A/C amplifier via CAN communication and BEAN communication.
The A/C amplifier reads the difference between compressor speed and engine speed. When the difference becomes too large, the A/C amplifier determines that the compressor locks, and turns the magnetic clutch off.

DTC No.
DTC Detection Condition
Trouble Area
B1422/22
Open or short in compressor lock sensor circuit
  1. A/C compressor (A/C lock sensor)
  2. Compressor drive belt
  3. Harness or connector between compressor and magnetic clutch (A/C lock sensor)
  4. A/C amplifier
  5. CAN communication system
  6. Multiplex communication system (BEAN)

WIRING DIAGRAM


E147293E02


INSPECTION PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
  1. Use Techstream to check if the CAN communication system is functioning normally.

    Result:
    Result
    Proceed to
    CAN DTC is not output
    A
    CAN DTC is output
    B



B
GO TO CAN COMMUNICATION SYSTEM
A


2.CHECK MULTIPLEX COMMUNICATION SYSTEM
  1. Use Techstream to check if the multiplex communication system (BEAN) is functioning normally.

    Result:
    Result
    Proceed to
    BEAN DTC is not output
    A
    BEAN DTC is output
    B



B
GO TO MULTIPLEX COMMUNICATION SYSTEM
A


3.INSPECT A/C AMPLIFIER


    E145185E01
  1. Remove the A/C amplifier with the connectors still connected.



    E116941E03
  1. Measure the waveform of the connector.
    Item
    Contents
    Tool setting
    200 mV/DIV., 10 ms./DIV.
    Vehicle condition
    Engine is running
    A/C switch: ON
    Blower switch: LO

    Standard:
    Tester Connection
    Condition
    Specified Condition
    A9-9 (LOCK) - A9-24 (SG-6)
    Engine is running
    A/C switch: ON
    Blower switch: LO
    Pulse generation

    Result:
    Result
    Proceed to
    NG
    A
    OK (When troubleshooting according to the PROBLEM SYMPTOMS TABLE)
    B
    OK (When troubleshooting according to the DTC)
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C
REPLACE A/C AMPLIFIER
A


4.INSPECT COMPRESSOR AND MAGNETIC CLUTCH (A/C LOCK SENSOR)


    E145186E01
  1. Disconnect the connector from the A/C compressor.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A31-1 (SSR+) - A31-2 (SSR-)
    Always (at 20°C (68°F))
    160 to 320 Ω



NG
REPLACE COMPRESSOR AND MAGNETIC CLUTCH (A/C LOCK SENSOR)
OK


5.CHECK HARNESS AND CONNECTOR (A/C AMPLIFIER - A/C LOCK SENSOR)


    E143742E29
  1. Disconnect the connector from the A/C amplifier.



    E124442E07
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A9-9 (LOCK) - A31-1 (SSR+)
    Always
    Below 1 Ω
    A9-24 (SG-6) - A31-2 (SSR-)
    Always
    Below 1 Ω
    A9-9 (LOCK) - Body ground
    Always
    10 kΩ or higher
    A9-24 (SG-6) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE A/C AMPLIFIER