RADIATOR > REMOVAL |
| 1. REMOVE V-BANK COVER SUB-ASSEMBLY |
![]() |
Hold the front of the V-bank cover and raise it to disengage the 2 clips on the front of the cover. Continue to raise the cover to disengage the clip on the rear of the cover and remove the cover.
| 2. REMOVE NO. 1 ENGINE UNDER COVER |
![]() |
Remove the 8 bolts, 4 clips and No. 1 engine under cover assembly.
| 3. DRAIN ENGINE COOLANT |
Loosen the radiator drain cock plug.

Remove the radiator cap sub-assembly from the radiator assembly.
Loosen the 2 cylinder block drain cock plugs.
| 4. REMOVE NO. 2 AIR CLEANER INLET |
![]() |
Disconnect the vacuum switching valve clamp.
Disconnect the 2 vacuum hoses.
Remove the 2 bolts and No. 2 air cleaner inlet.
| 5. REMOVE BATTERY |
![]() |
Disconnect the negative battery terminal.
Disconnect the positive battery terminal.
Loosen the nut, and remove the bolt and battery clamp.
Remove the battery and battery tray.
| 6. REMOVE FRONT BUMPER ASSEMBLY |
![]() |
Remove the 4 screws and separate the fender liner from the front bumper assembly.
![]() |
Remove the 8 screws and separate the engine under cover from the front bumper assembly.
![]() |
Remove the 5 clips.
![]() |
Disengage the claws on the left and right sides of the front bumper and pull the front bumper toward the front of the vehicle as shown in the illustration.
| 7. REMOVE FRONT BUMPER ENERGY ABSORBER |
| 8. REMOVE NO. 1 AIR CLEANER INLET |
![]() |
Remove the bolt and No. 1 air cleaner inlet.
| 9. DISCONNECT RADIATOR RESERVE TANK HOSE OR PIPE |
![]() |
Disconnect the radiator reserve tank hose or pipe from the radiator.
| 10. DISCONNECT NO. 1 RADIATOR HOSE |
![]() |
Disconnect both connections of the No. 1 radiator hose from the radiator.
| 11. DISCONNECT NO. 2 RADIATOR HOSE |
![]() |
Disconnect the No. 2 radiator hose from the radiator.
| 12. REMOVE HOOD LOCK RELEASE LEVER PROTECTOR |
![]() |
Disengage the 4 claws and remove the hood lock release lever protector.
| 13. REMOVE HOOD LOCK ASSEMBLY |
With Hood Courtesy Switch:
Disconnect the connector.
![]() |
Remove the 3 bolts.
![]() |
Disconnect the cable and remove the hood lock assembly.
| 14. REMOVE HOOD LOCK SUPPORT SUB-ASSEMBLY |
![]() |
Disconnect the ambient temperature sensor connector.
![]() |
Detach the clamp.
Disconnect the low pitched horn and high pitched horn connectors.
![]() |
Remove the 2 bolts and hood lock support sub-assembly.
| 15. DISCONNECT COOLING FAN ECU CONNECTOR |
![]() |
Disconnect the cooling fan ECU connector.
Detach the clamp.
| 16. REMOVE RADIATOR UPPER SUPPORT SUB-ASSEMBLY |
![]() |
Remove the 4 bolts and radiator upper support sub-assembly.
| 17. DISCONNECT NO. 2 OIL COOLER OUTLET TUBE SUB-ASSEMBLY |
Disconnect the No. 1 oil cooler inlet and No. 1 oil cooler outlet hoses from the No. 2 oil cooler outlet tube sub-assembly.

Disconnect the No. 1 transmission oil cooler hoses from the radiator.
Remove the 2 bolts and No. 2 oil cooler outlet tube sub-assembly.
| 18. REMOVE HEADLIGHT ASSEMBLY RH |
Use the same procedures for the RH side and LH side.
| 19. REMOVE RADIATOR SIDE DEFLECTOR RH |
![]() |
Disengage the 3 claws and remove the radiator side deflector RH.
| 20. REMOVE HEADLIGHT BRACKET RH |
![]() |
Remove the 3 nuts and headlight bracket RH.
| 21. REMOVE PRESSURE FEED TUBE ASSEMBLY |
![]() |
Remove the 2 bolts.
| 22. REMOVE RADIATOR SUPPORT CUSHION |
![]() |
Remove the 2 radiator support cushions from the No. 1 radiator support.
| 23. REMOVE NO. 1 RADIATOR SUPPORT |
Detach the clamp.
![]() |
Remove the 6 bolts and No. 1 radiator support.
| 24. REMOVE RADIATOR ASSEMBLY WITH FAN SHROUD AND FAN MOTOR |
![]() |
Remove the 2 bolts and separate the condenser assembly from the radiator assembly with fan shroud and fan motor.
![]() |
Remove the radiator assembly with fan shroud and fan motor from the body.
| 25. REMOVE FAN SHROUD WITH FAN MOTOR |
![]() |
Remove the 2 bolts and fan shroud with fan motor from the radiator.
| 26. REMOVE RADIATOR SUPPORT LOWER |
![]() |
Remove the 2 radiator support lowers from the radiator assembly.
| 27. REMOVE NO. 2 RADIATOR SUPPORT |
![]() |
Remove the 2 bolts and No. 2 radiator support from the radiator.
| 28. DISCONNECT INLET SUB-ASSEMBLY |
![]() |
Disconnect the inlet hose from the radiator.
Remove the bolt and inlet sub-assembly from the radiator.