Home › ENGINE › 2GR-FE IGNITION › IGNITION COIL AND SPARK PLUG

IGNITION COIL AND SPARK PLUG > REMOVAL

for Preparation Click here



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


2. DRAIN ENGINE COOLANT


3. REMOVE FRONT WIPER ARM HEAD CAP


    I035789E01
  1. Using a small screwdriver, remove the 2 front wiper arm covers.

    HINT:
    Tape up the screwdriver tip before use.



4. REMOVE FRONT WIPER ARM RH
  1. Operate the wiper, and stop the windshield wiper motor assembly to the automatic stop position.

  1. Remove the nut and the FR wiper arm RH.



5. REMOVE FRONT WIPER ARM LH
  1. Remove the nut and the FR wiper arm LH.



6. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    I035790E01
  1. Remove the 6 claws and the cowl top ventilator louver sub-assembly.



7. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
  1. Disconnect the connector.



    I035791E01
  1. Remove the 4 bolts and wiper motor & link assembly.



8. REMOVE NO. 1 COWL TOP TO COWL BRACE INNER


    A162429
  1. Remove the 2 bolts and the No. 1 cowl top to cowl brace inner.



9. REMOVE COWL TOP PANEL SUB-ASSEMBLY OUTER FRONT


A162430
  1. Remove the wire harness clamp.

  1. Disconnect the fuel pump resistor connector.

  1. Remove the 7 bolts and the cowl top panel outer front.



10. REMOVE NO. 1 ENGINE UNDER COVER


11. REMOVE V-BANK COVER SUB-ASSEMBLY


    A162365
  1. Hold the front of the V-bank cover and raise it to disengage the 2 clips on the front of the cover. Continue to raise the cover to disengage the clip on the rear of the cover and remove the cover.

    NOTICE:
    Attempting to disengage both front and rear clips at the same time may cause the cover to break.



12. REMOVE AIR CLEANER CAP SUB-ASSEMBLY


    A135112E01
  1. Disconnect the 3 vacuum hoses.



    A135113E01
  1. Remove the No. 2 ventilation hose and air cleaner hose band.

  1. Disconnect the vacuum hose (EVAP) from the air cleaner hose.



    A163204
  1. Remove the 2 bolts and air cleaner cap sub-assembly.



13. REMOVE INTAKE AIR SURGE TANK ASSEMBLY


    A129464E10
  1. Disconnect the 2 water by-pass hoses from the throttle with motor body assembly. (*1)

  1. Disconnect the fuel vapor feed hose assembly.(*2)

  1. Disconnect the throttle with motor body assembly connector and clamp. (*3)



    A162431E01
  1. Disconnect the No. 1 ventilation hose. (*4)

  1. Disconnect the union to check valve hose. (*5)



    A129467
  1. Disconnect the connector.



    A129468E11
  1. Using a 5 mm socket hexagon wrench, remove the 4 bolts. (*1)

  1. Remove the 2 nuts, 2 bolts, and intake air surge tank. (*2)

  1. Remove the gasket from the intake air surge tank.



14. REMOVE NO. 1 SURGE TANK STAY


    A161840
  1. Remove the 2 bolts and nut and disconnect the 2 harness clamps.



    A134967
  1. Remove the bolt and No. 1 surge tank stay.



15. REMOVE IGNITION COIL ASSEMBLY


    A134966E01
  1. Disconnect the 6 ignition coil connectors.

  1. Remove the 6 bolts and 6 ignition coils.



16. REMOVE SPARK PLUG


    A137604
  1. Remove the 6 spark plugs.