THEFT DETERRENT SYSTEM > SYSTEM DESCRIPTION |
| OUTLINE OF THEFT DETERRENT SYSTEM |
When the theft deterrent system detects that the vehicle is being tampered with, the system sets off the alarm, causing the horns to sound and the lights to light up or blink in order to alert people around the vehicle to the theft.
The theft deterrent system has 2 modes; one is the active arming mode (see ACTIVE ARMING MODE) and the other is passive arming mode (see PASSIVE ARMING MODE). The passive arming mode can be switched ON/OFF using the specified method.
Each mode has 4 states; a disarmed state, an arming preparation state, an armed state and an alarm sounding state.
Disarmed state:
Arming preparation state:
Armed state:
Alarm sounding state:
| Alarm Method | Headlight | Blinking (approx. 0.4 second cycles) |
| Taillight | Blinking (approx. 0.4 second cycles) | |
| Hazard Warning Light | Blinking (cycles of flasher relay) | |
| Interior Light | Illuminating | |
| Vehicle Horn | Sounding (approx. 0.4 second cycles) | |
| Security Horn | Sounding (approx. 0.4 second cycles) | |
| Alarm Time | Approx. 60 sec. | |
| ACTIVE ARMING MODE |
Active arming mode

| Condition | Item |
| Condition (1) | (No key in ignition key cylinder)
|
| Condition (2) |
|
| Condition (3) |
|
| Condition (4) |
|
| Condition (5) |
|
| Condition (6) |
|
| Condition (7) |
|
| PASSIVE ARMING MODE |
Passive arming mode

| Condition | Item |
| Condition (1) |
|
| Condition (2) |
|
| Condition (3) |
|
| Condition (4) |
|
| Condition (5) |
|
| Condition (6) |
|
| Condition (7) |
|
| Condition (8) |
|
| FORCED DOOR LOCK CONTROL |
The forced door lock control prevents the vehicle from being tampered with. Immediately after a door is unlocked (alarm starts), the door is forced to lock by a forced door lock signal.
Conditions that force the doors to lock:
No key is in the ignition key cylinder and both of the following conditions are met.
| ALARM MEMORY FUNCTION |
If the alarm is set off (tampering is detected) while the theft deterrent system is armed, it will be recorded by the alarm memory function. Whenever you cancel the theft deterrent system, the alarm memory function causes the taillights to light up for 2 seconds in order to inform you that the alarm has been set off.
Conditions of the alarm memory function that cause the taillights to light up:
When the theft deterrent system has entered into the alarm sounding state (tampering has been detected) even once, the taillights will light up for 2 seconds if any of the following conditions is met.
| PANIC ALARM CONTROL |
The panic alarm control makes it possible to voluntarily set off the panic alarm by pressing the PANIC switch on the wireless transmitter.
Conditions that cause the panic alarm control to set off the panic alarm:
The panic alarm control sets off the panic alarm by pressing the PANIC switch on the wireless transmitter for over 2, 4 seconds under the following conditions:
Conditions that cause the panic alarm control to shut off the alarm:
The panic alarm control shuts off the panic alarm when any of the following conditions is met during panic alarm operation:
| SECURITY INDICATOR OUTPUT |
The multiplex network body ECU outputs a signal to light up the security indicator, according to the state of the theft deterrent system. However, some of the actual lighting conditions of the security indicator are different from the output signals of the multiplex network body ECU.
| State of Theft Deterrent System* | Security Indicator | |
| Output Signals from Body ECU | Actual Lighting Condition | |
| Disarmed state (1), (2) | OFF | OFF (Immobiliser system unset) BLINKING (Immobiliser system set) |
| Arming preparation state | ON | ON |
| Armed state | OFF | BLINKING |
| Alarm sounding state | ON | ON |
| Time | Security Indicator |
| 0.2 sec. | ON |
| 1.8 sec. | OFF |