Home › ENGINE › 2GR-FE COOLING › COOLANT

COOLANT > REPLACEMENT

for Preparation Click here



1. REMOVE NO. 1 ENGINE UNDER COVER


    A162362
  1. Remove the 8 bolts, 4 clips and No. 1 engine under cover assembly.



2. REMOVE V-BANK COVER SUB-ASSEMBLY


    A162365
  1. Hold the front of the V-bank cover and raise it to disengage the 2 clips on the front of the cover. Continue to raise the cover to disengage the clip on the rear of the cover and remove the cover.

    NOTICE:
    Attempting to disengage both front and rear clips at the same time may cause the cover to break.



3. DRAIN ENGINE COOLANT


  1. Loosen the radiator drain cock plug.


    A161473E01

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Remove the radiator cap sub-assembly from the radiator assembly.

    NOTICE:
    Do not remove the radiator cap sub-assembly while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the 2 cylinder block drain cock plugs.



4. ADD ENGINE COOLANT
  1. Tighten the radiator drain cock plug by hand.

  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for cylinder block drain cock plugs

  1. Remove the air drain cock plug from the water inlet housing.



    A162799E01
  1. Loosen the air drain plug at the top of the radiator 3 or 4 turns.

  1. Add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the engine air drain cock hole. Then install the air drain cock plug to the water inlet housing.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for air drain cock plug

  1. Continue to add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the radiator air drain hole. Then close the air drain plug at the top of the radiator.

    HINT:
    If the coolant level at the radiator inlet opening drops after squeezing the No. 1 and No. 2 radiator hoses, add coolant.

  1. Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).

    Standard capacity:
    11.3 liters (12.0 US qts, 10.0 Imp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    2. Contact your TOYOTA dealer for further details.

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Slowly pour coolant into the radiator reservoir tank until it reaches the FULL line.

  1. Squeeze the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level is low, add coolant.

  1. Bleed air from the cooling system.

    1. Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.

      HINT:
      The thermostat open timing can be confirmed by squeezing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.

    2. Maintain the engine speed at 2500 to 3000 rpm.

    3. Squeeze the inlet and outlet radiator hoses several times by hand to bleed air.

      CAUTION:
      When squeezing the radiator hoses:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the radiator fan.

      NOTICE:
      1. Make sure that the radiator reservoir still has some coolant in it.
      2. If the coolant temperature gauge indicates an excessive temperature, turn off the engine and let it cool.
      3. If there is not enough coolant, the engine may overheat or be seriously damaged.
      4. If the radiator reservoir does not have enough coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the FULL line.

  1. Stop the engine and wait until the engine coolant cools down.

  1. Add engine coolant to the FULL line on the radiator reservoir.



5. INSPECT FOR COOLANT LEAK

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

NOTICE:
Before performing each inspection, turn the A/C switch OFF.



    A161453
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.



6. INSTALL V-BANK COVER SUB-ASSEMBLY


    A162365
  1. Fit the 3 retainers and install the V-bank cover.



7. INSTALL NO. 1 ENGINE UNDER COVER


    A162362
  1. Install the No. 1 engine under cover sub-assembly with the 8 bolts and 4 clips.