DTC P0017 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B) |
DTC P0019 Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor B) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0017 | Deviations in crankshaft position sensor and VVT sensor 1 (for exhaust camshaft) 2 signals (2 trip detection logic) |
|
| P0019 | Deviations in crankshaft position sensor and VVT sensor 2 (for exhaust camshaft) 2 signals (2 trip detection logic) |
| Related DTCs | Deviation in crankshaft position sensor signal and camshaft position sensor signal |
| Required Sensors / Components (Main) | Timing chain/belt |
| Required Sensors / Components (Related) | None |
| Frequency of Operation | Once per driving cycle |
| Duration | Less than 60 seconds |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| The monitor will run whenever these DTCs are not present | P0013, P0023 (Exhaust OCV bank 1, 2) P0100, P0102, P0103 (MAF meter) P0115, P0117, P0118 (ECT sensor) P0125 (Insufficient ECT for closed loop) P0335 (CKP sensor) |
| VVT feedback mode | Executing |
| VVT | Maximum advanced position |
| Engine RPM | 500 to 1000 rpm |
| One of the following conditions is met: | Condition 1 or 2 |
| 1. VVT learning value | Less than 77° CA |
| 2. VVT learning value | More than 102° CA |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0017 AND P0019) |
Connect the Techstream to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Trouble Code.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| P0017 or P0019 | A |
| P0017 or P0019 and other DTCs | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE OIL CONTROL VALVE FOR EXHAUST CAMSHAFT) |
Connect the Techstream to the DLC3.
Start the engine and turn the tester on.
Warm up the engine.
Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the VVT Exhaust Linear (Bank 1) or Control the VVT Exhaust Linear (Bank 2).
Check the engine speed while operating the oil control valve using the tester.
| Tester Operation | Specified Condition |
| OCV OFF | Normal engine idle speed |
| OCV ON | Engine idles roughly or stalls (soon after OCV switched from OFF to ON) |
|
| ||||
| OK | |
| 3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0017 OR P0019) |
Connect the Techstream to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Clear the DTCs (Click here).
Start the engine and warm it up.
Switch the check mode using the tester (Click here).
Drive the vehicle for more than 10 minutes.
Read the DTCs using the tester.
|
| ||||
| OK | ||
| ||
| 4.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMP TEETH ON TIMING CHAIN) |
![]() |
Remove the cylinder head covers RH and LH.
Turn the crankshaft to align the matchmarks of the crankshaft.
Align the notch of the crankshaft pulley to the "0" position.
Check if the matchmarks of the camshaft pulley and camshaft bearing cap align.
Turn the crankshaft clockwise by 360° if the matchmarks do not align. Check if they align once again.
|
| ||||
| OK | |
| 5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT) |
Remove the exhaust camshaft timing oil control valve.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | 20°C (68°F) | 6.9 to 7.9 Ω |
![]() |
Apply the positive battery voltage to terminal 1 and the negative battery voltage to terminal 2. Check the valve operation.
Reinstall the camshaft timing oil control valve.
|
| ||||
| OK | |
| 6.CHECK OIL CONTROL VALVE FILTER AND PIPE |
![]() |
Remove the oil pipe No. 1 or oil pipe assembly.
Remove the oil control valve filter.
Check that the filter and pipe are not clogged.
|
| ||||
| OK | |
| 7.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY |
| NEXT | |
| 8.CHECK WHETHER DTC OUTPUT RECURS |
Connect the Techstream to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Clear the DTCs (Click here).
Start the engine and warm it up.
Switch the check mode using the tester (Click here).
Drive the vehicle for more than 10 minutes.
Confirm that no DTC is set using the tester.
|
| ||||
| OK | ||
| ||