Home › Vehicle Exterior › BODY PANEL › FRONT FENDER APRON
BM3650E _01 Vehicle Exterior _083396 BODY PANEL _0402520 FRONT FENDER APRON F

BODY PANEL  FRONT FENDER APRON  ASSEMBLY REPLACEMENT (PATTERN 1)  


K153136

REMOVE THE ADHESIVE


a.

Detach any mechanical connecting elements where required.


b.

Heat the adhesive flange with a hot air blower.

NOTICE:

Do not exceed the maximum object temperature of 250°C.



c.

Use pliers or a chisel to peel off the component.

NOTICE:

Do not damage adjacent components.



d.

Remove adhesive residue from the adhesive flange.



REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108826

Cut with Disc Sander etc.

a.
K152726C01
0.063,0.979 0.375,1.135 0.313,0.156 10 false *a: 1.635,1.969 1.948,2.125 0.313,0.156 10 false *b: 2.521,1.99 2.833,2.146 0.313,0.156 10 false *a: 1.083,1.948 1.396,2.104 0.313,0.156 10 false *a:
*a Self-tapping Screw
*b Rivet


Remove the self-tapping screws and adhesive connections in the areas (1) and (2).


b.

Remove the rivets and adhesive connections in area (3).


c.
K152727

Remove the weld points in areas (1).


d.

Remove the weld points in the areas (2) from the inside of the wheel arch with the belt sander.


e.
K152728C01
0.896,0.01 1.208,0.167 0.313,0.156 10 false *a: 0.031,1.219 0.344,1.375 0.313,0.156 10 false *a: 2.594,0.802 2.906,0.958 0.313,0.156 10 false *a:
*a Rivet


Remove the rivets and adhesive connections in area (1) and (2).


f.

Drill out the rivets and adhesive connections in area (2) from the outside through the carrier support of the rear wheel arch.


g.
K152729C01
2.74,0.115 3.052,0.271 0.313,0.156 10 false *a: 3.031,1.365 3.344,1.521 0.313,0.156 10 false *a:
*a Rivet


Remove the rivets and adhesive connections in area (1) and (2).



PREPARE NEW PART


a.

Adjust and secure front fender apron sub-assy.


b.
K152730C01
0.542,0.531 0.417,0.25 0.417,0.25 0.25,0.25 false 0.073,0.188 0.385,0.344 0.313,0.156 10 false *1
*1 FRONT FENDER APRON SUB-ASSY


Transfer hole pattern in the areas (1) and (2) from the front side member sub-assy to the front fender apron sub-assy. (See the introduction)


c.

Drill out holes in areas (1) and (2) with 6.8 mm (0.27 in.) diameter.


d.
K152731

Transfer the hole pattern in the areas (1) from the rear wheel arch to the front fender apron sub-assy. (See the introduction)


e.

Transfer the hole pattern in the area (2) from the carrier support rear wheel arch to the front fender apron sub-assy. (See the introduction)


f.

Drill out holes in areas (1) and (2) with 6.8 mm (0.27 in.) diameter.


g.
K152732

Transfer the hole pattern in the areas (1) and (2) to the front fender apron sub-assy. (See the introduction)


h.

Drill out holes in areas (1) and (2) with 6.8 mm (0.27 in.) diameter.


i.
K152733C01
0.271,0.823 0.438,0.823 0.438,0.823 0.521,1.083 false 0.094,0.74 0.406,0.896 0.313,0.156 10 false *1
*1 RADIATOR SUPPORT UPPER


Adjust and secure the support of the radiator support upper.


j.

Transfer holes for blind rivet connections in areas (1) and (2). (See the introduction)

HINT:

Carry out bore holes in number and position analogous to the series production.



k.

Drill out holes in areas (1) with 4.2 mm (0.17 in.) diameter.


l.

Drill out holes in areas (2) with 6.8 mm (0.27 in.) diameter.


m.
K152734C01
1.583,2 1.75,2 1.75,2 1.875,1.646 false 1.375,1.375 1.531,1.573 0.156,0.198 10 false A 1.323,0.979 1.479,1.177 0.156,0.198 10 false A 1.24,0.719 1.396,0.917 0.156,0.198 10 false A 1.76,1.448 1.917,1.646 0.156,0.198 10 false A 1.427,1.917 1.74,2.115 0.313,0.198 10 false *1
*1 RADIATOR SUPPORT TO FRONT FENDER BRACKET


Transfer the hole pattern in the areas (1) from the used to the front fender apron sub-assy of the radiator support upper. (See the introduction)


n.

Draw on hole pattern in the areas (2) on the radiator support to front fender bracket.

NOTICE:

Do not drill holes may be drilled in the areas A.



o.

Drill out holes in areas (1) with 4.2 mm (0.17 in.) diameter.


p.

Drill out holes in areas (2) with 6.8 mm (0.27 in.) diameter.


q.
K152735C01
1,2 1.167,2 1.167,2 1.49,1.323 false 0.833,0.167 1,0.167 1,0.167 1.167,0.5 false 0.854,1.927 1.01,2.125 0.156,0.198 10 false A 0.667,0.104 0.979,0.26 0.313,0.156 10 false *1
*1 FRONT SIDE MEMBER BRACKET SUB-ASSY


Transfer hole pattern in the areas A from the used part to the front side member bracket sub-assy (1) and the front fender apron sub-assy (2). (See the introduction)


r.

Drill out holes in areas (1) and (2) with 6.8 mm (0.27 in.) diameter.



PREPARE THE ALUMINIUM SURFACE (USED PART) FOR STRUCTURAL BONDING


a.

Remove coarse contamination from the bonding surfaces using solvent cleaner R2.

Expendable materials:
Cleaner R2 500ml 08879-WA010



b.

Clean the bonding surfaces using solvent cleaner R1.

Expendable materials:
Cleaner R1 100ml, Bottle 08833-WA050



c.

Remove oxide layers or paint from bonding surfaces using a stainless steel wire brush or sandpaper with 120 grain.

HINT:

Grind the bonding surface down to the bare metal.



d.

Clean the bonding surfaces using solvent cleaner R1.

Expendable materials:
Cleaner R1 100ml, Bottle 08833-WA050



e.

Allow cleaned surfaces to dry for approximately 5 min.

HINT:

The bonding surfaces must be completely dry.



f.

Flame spray the bonding surfaces with primer P2.

Expendable materials:
Primer P2 50ml, Gas cartridge 08833-WA240


HINT:
·

Go over the bonding surfaces slowly with the flame.

·

Flaming with the blue part of the flame must be avoided.

·

Condensation water appears on the area that is still uncoated. The condensation water in the line of the flame must evaporate completely.




g.

Immediately following flame spraying, coat the bonding surfaces that are still warm (approximately 50°C) with primer P1. Apply the primer P1 with a brush, cotton ball or similar item.

Expendable materials:
Primer P1 50ml, Bottle 08833-WA030



h.

Allow the bonding surfaces to dry for approximately 5 min.


i.
K152736

Prepare engine support in the areas (1) for the bonding aluminium used part.

Expendable materials:
Cleaner R1 100ml, Bottle 08833-WA050
Primer P1 50ml, Bottle 08833-WA030
Primer P2 50ml, Gas cartridge 08833-WA240



j.
K152737

Prepare rear wheel arch in the area (1) for the steel bonding.


k.

Prepare engine bulkhead in the area (2) for the steel bonding.

Expendable materials:
Cleaner R1 100ml, Bottle 08833-WA050




PREPARE THE STEEL SURFACE (USED PART AND NEW PART) FOR STRUCTURAL BONDING


a.

Remove coarse contamination from the bonding surfaces using solvent cleaner R2.

Expendable materials:
Cleaner R2 500ml 08879-WA010



b.

Clean the bonding surfaces using solvent cleaner R1.

Expendable materials:
Cleaner R1 100ml, Bottle 08833-WA050



c.

Grind the bonding surface down to the bare metal.


d.

Clean the bonding surface with cleaning agent R1.

Expendable materials:
Cleaner R1 100ml, Bottle 08833-WA050



e.
K152738

Prepare front inner A-pillar in the area (1) for the steel bonding.


f.

Prepare the front body pillar gusset lower in the areas (2) for joining by welding.



PREPARE THE ALUMINIUM SURFACE (NEW PART) FOR STRUCTURAL BONDING


a.

Do not sand the bonding surfaces.


b.

Remove coarse contamination from the bonding surfaces using solvent cleaner R2.

Expendable materials:
Cleaner R2 500ml 08879-WA010



c.

Clean the bonding surfaces using solvent cleaner R1.

Expendable materials:
Cleaner R1 100ml, Bottle 08833-WA050



d.
K152739

Prepare front fender apron sub-assy in the areas (1) for the aluminium new part bonding.


e.

Prepare front fender apron sub-assy in the areas (2) for the aluminium new part bonding.

Expendable materials:
Cleaner R2 500ml 08879-WA010
Cleaner R1 100ml, Bottle 08833-WA050



f.
K152740

Prepare front fender apron sub-assy in the areas (1) for the aluminium new part bonding.


g.

Prepare front fender apron sub-assy in the areas (2) for the aluminium new part bonding.

Expendable materials:
Cleaner R2 500ml 08879-WA010
Cleaner R1 100ml, Bottle 08833-WA050



h.
K152741

Prepare radiator support upper on the inside in the area (1) for the aluminium used part bonding.


i.

Prepare the radiator support upper in the areas (2) for joining by welding.

Expendable materials:
Cleaner R2 500ml 08879-WA010
Cleaner R1 100ml, Bottle 08833-WA050



j.
K152754

Prepare the front fender apron sub-assy in area (1) for the aluminium new part bonding.


k.

Prepare the front side member bracket sub-assy in area (2) for the aluminium new part bonding.

Expendable materials:
Cleaner R2 500ml 08879-WA010
Cleaner R1 100ml, Bottle 08833-WA050
Primer P1 50ml, Bottle 08833-WA030




INSTALLATION


Symbol Meaning
K108825

Plug Weld

a.
K152742C01
0,0 0,0 false
K108837

Adhesive


Apply adhesive to the bonding surfaces (1) on the vehicle.

Adhesive:
K1 Bodywork Adhesive 195ml 08833-WA210



b.
K152743C01
0,0 0,0 false
K108837

Adhesive


Apply adhesive to the bonding surfaces (1) and (2)on the vehicle.

Adhesive:
K1 Bodywork Adhesive 195ml 08833-WA210



c.
K152744C01
0,0 0,0 false
K108837

Adhesive


Apply adhesive to the bonding surfaces (1) on the vehicle.

Adhesive:
K1 Bodywork Adhesive 195ml 08833-WA210



d.
K152745C01
0,0 0,0 false
K108837

Adhesive


Apply adhesive to the marked bonding surfaces on the front fender apron sub-assy.

Adhesive:
K1 Bodywork Adhesive 195ml 08833-WA210



e.
K152746

Place the radiator support upper (1) on the front fender apron sub-assy (new part) (2) and position on the vehicle.


f.
K152747C01
0.24,0.927 0.552,1.083 0.313,0.156 10 false *a: 1.323,1.906 1.635,2.063 0.313,0.156 10 false *b: 3.083,1.823 3.396,1.979 0.313,0.156 10 false *b: 3.104,0.573 3.417,0.729 0.313,0.156 10 false *b:
*a BLIND RIVET N1 HEMLOCK 813
*b BLIND RIVET N2 HEMLOCK 815


Rivet the front fender apron sub-assy in areas (1) with the blind rivets N1.

Expendable materials:
BLIND RIVET N1 HEMLOCK 813 φ 6.5 mm ; clamping range 2.8-4.8 mm 90118WA664



g.

Rivet the front fender apron sub-assy in areas (2) with the blind rivets N2.

Expendable materials:
BLIND RIVET N2 HEMLOCK 815 φ 6.5 mm ; clamping range 4.8-6.8 mm 90118WA665



h.
K152748C01
0.073,1.115 0.385,1.271 0.313,0.156 10 false *a:
*a BLIND RIVET N1 HEMLOCK 813


Rivet the front fender apron sub-assy in areas (1) with the blind rivets N1.

Expendable materials:
BLIND RIVET N1 HEMLOCK 813 φ 6.5 mm ; clamping range 2.8-4.8 mm 90118WA664



i.
K152749C01
2.542,0.052 2.854,0.208 0.313,0.156 10 false *a: 3.031,1.354 3.344,1.51 0.313,0.156 10 false *a:
*a BLIND RIVET N1 HEMLOCK 813


Rivet the front fender apron sub-assy in areas (1) and (2) with the blind rivets N1.

Expendable materials:
BLIND RIVET N1 HEMLOCK 813 φ 6.5 mm ; clamping range 2.8-4.8 mm 90118WA664



j.
K152750C01
0.458,1.927 0.771,2.083 0.313,0.156 10 false *a: 0.094,0.719 0.406,0.875 0.313,0.156 10 false *b: 3.094,0.896 3.406,1.052 0.313,0.156 10 false *c: 1.458,0.021 1.771,0.177 0.313,0.156 10 false *b: 1.323,1.927 1.635,2.083 0.313,0.156 10 false *c:
*a BLIND RIVET N6
*b BLIND RIVET N1 HEMLOCK 813
*c BLIND RIVET N2 HEMLOCK 815


Rivet the radiator support upper in areas (1) with the blind rivets N6.

Expendable materials:
BLIND RIVET N6 φ4mm, clamping range 3-5 mm 90118WA667



k.

Rivet the radiator support upper in areas (2) with the blind rivets N1.

Expendable materials:
BLIND RIVET N1 HEMLOCK 813 φ 6.5 mm ; clamping range 2.8-4.8 mm 90118WA664



l.

Rivet the radiator support upper in areas (3) with the blind rivets N2.

Expendable materials:
BLIND RIVET N2 HEMLOCK 815 φ 6.5 mm ; clamping range 4.8-6.8 mm 90118WA665



m.
K152751C01
1.042,0.094 1.354,0.25 0.313,0.156 10 false *a: 1.146,1.979 1.458,2.135 0.313,0.156 10 false *b: 2.104,0.063 2.417,0.219 0.313,0.156 10 false *a: 3.104,1.354 3.417,1.51 0.313,0.156 10 false *a:
*a BLIND RIVET N1 HEMLOCK 813
*b BLIND RIVET N6


Rivet the radiator support upper in the areas (1) with blind rivets N1.

Expendable materials:
BLIND RIVET N1 HEMLOCK 813 φ 6.5 mm ; clamping range 2.8-4.8 mm 90118WA664



n.

Rivet the radiator support upper in areas (2) with the blind rivets N6.

Expendable materials:
BLIND RIVET N6 φ4mm, clamping range 3-5 mm 90118WA667



o.
K152752C01
2.417,0.115 2.729,0.271 0.313,0.156 10 false *a:
*a BLIND RIVET N6


Rivet the radiator support upper in area (1) with the blind rivets N6.

Expendable materials:
BLIND RIVET N6 φ4mm, clamping range 3-5 mm 90118WA667



p.
K152753

Weld the radiator support upper with the carrier support of the front body pillar gusset lower at the marked points.


q.
K152755C01
0,0 0,0 false
K108837

Adhesive


Apply adhesive to the bonding surface (1).

Adhesive:
K1 Bodywork Adhesive 195ml 08833-WA210



r.
K152756C01
1.219,1.969 1.531,2.125 0.313,0.156 10 false *a:
*a BLIND RIVET N1 HEMLOCK 813


Rivet the front side member bracket sub-assy in area (1) with the blind rivets N1.

Expendable materials:
BLIND RIVET N1 HEMLOCK 813 φ 6.5 mm ; clamping range 2.8-4.8 mm 90118WA664




INSTALL THE EMC SCREW (EMC = ELECTROMAGNETIC COMPATIBILITY)


a.

After adhesive has fully hardened: Drill hole with diameter of 4.2 mm.

HINT:

The EMC screw can only be screwed in and sealed with sealant once the adhesive has fully hardened.



b.
K152757C01
0.417,0.917 0.583,0.917 0.583,0.917 1,1.521 false 2.167,2 2.333,2 2.333,2 2.792,1.49 false 0.24,0.813 0.552,0.969 0.313,0.156 10 false *a 1.99,1.906 2.219,2.146 0.229,0.24 10 false *a
*a EMC SCREW


Install EMC screw in area (1) and (2).

Expendable materials:
EMC SCREW SF Plus, M5x15 90118WA666



c.

Apply seam seal to the area (1) and (2).

Expendable materials:
Seam Seal 310ml 08826-WA220



d.
K152758

Apply seam seal to the rivets.

Expendable materials:
Seam Seal 310ml 08826-WA220



e.

After welding, apply body sealer and undercoating to the corresponding parts. (See the painting/coating)


f.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.



POSTPROCESSES


a.
K152759

At the bolting points (1) of the top stiffening plate strut it is necessary to cut the M10 (pitch:1.5) thread.


b.

Renew screws.