Home › Vehicle Exterior › BODY PANEL › FRONT BODY PILLAR
BM3650E _01 Vehicle Exterior _083396 BODY PANEL _0402522 FRONT BODY PILLAR F

BODY PANEL  FRONT BODY PILLAR  CUT AND JOIN REPLACEMENT SECTIONS (PATTERN 2)  


K153142

REMOVE THE ADHESIVE


a.

Detach any mechanical connecting elements where required.


b.

Heat the adhesive flange with a hot air blower.

NOTICE:

Do not exceed the maximum object temperature of 250°C.



c.

Use pliers or a chisel to peel off the component.

NOTICE:

Do not damage adjacent components.



d.

Remove adhesive residue from the adhesive flange.



REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108820

Remove Weld Points
K108827

Cut and Join Location
K108829

Cut Location

a.

Mark and perform the separating cuts to match the specified dimensions.

NOTICE:

Thereby disconnect only the outer panel.



b.

Remove the weld points in areas (1).


c.

Remove the weld points and adhesive in area (2).


d.

Remove the adhesive in area (3).


e.

Remove the side panel sub-assy outer from the foamed sealing material in areas (4).

K152779C01
2,3.5 2.167,3.5 2.167,3.5 2.271,3.052 false 1.979,0.438 2.292,0.594 0.313,0.156 10 false *a 3.833,3.365 4.146,3.521 0.313,0.156 10 false *b 4.979,3.531 5.292,3.688 0.313,0.156 10 false *b 2.958,1.375 3.271,1.531 0.313,0.156 10 false *a 1.823,3.417 2.135,3.573 0.313,0.156 10 false *1
*1 SIDE PANEL SUB-ASSY OUTER - -
*a centre of hole *b 80 mm (3.15 in.) from the outer edge of the hole
K108837

Adhesive
K108840

Foamed Sealing Material



f.
K152780

Remove the remaining foamed sealing material (1) from the vehicles side.


g.
K152781

Remove the weld points in areas (1).


h.
K152782C01
0,0 0,0 false
K108840

Foamed Sealing Material


Mark the severance cuts (1) according to the schematic diagram and cut.

NOTICE:

Thereby disconnect only the outer panel.



i.

Remove the weld points in areas (2).


j.

Remove the foamed sealing material in area (3).


k.
K152783

Remove the weld points in areas (1).


l.

Remove the remaining panels (2) from the vehicle side.


m.
K152784

Remove the weld points in areas (1).



PREPARE NEW PART


a.
K152785C01
0.583,1.833 0.75,1.833 0.75,1.833 1,1.5 false 2.448,1.292 2.583,1 2.583,1 2.75,1 false 0.417,1.76 0.729,1.917 0.313,0.156 10 false *1 2.813,0.917 3.125,1.073 0.313,0.156 10 false A
*1 COWL SIDE PANEL SUB-ASSY


Remove the weld points in areas (1) and (2).


b.

Remove A from the new parts of cowl side panel sub-assy.


c.
K152786

Remove (1) from the new parts.



INSTALL THE FOAMED SEALING MATERIAL


HINT:
·

Schematic diagram is for example purposes.

·

Some parts may differ in certain details.



a.
K152602

Sand the contact surface of the cavity sealing (1) with sandpaper (#50-100).


b.

Clean the contact surface (1) with the cleaner R2.

Expendable materials:
Cleaner R2 500ml 08879-WA010



c.

On the contact surface (1), apply an approximately 15 mm (0.59 in.) bead (2) of brushable seam seal. If necessary apply a slightly thinner bead of brushable seam seal on each side, to prevent the sealant from running.

Expendable materials:
Brushable Seam Seal 310ml 08826-WA230



d.
K152787

Apply brushable seam seal on the front body pillar reinforcement lower foamed sealing material (1).


e.

Install foamed sealing material (1) in the front body pillar reinforcement lower.



INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108824

Plug Weld
K108825

Plug Weld
K108831

Butt Weld

a.
K152788C01
0.281,1.938 0.594,2.094 0.313,0.156 10 false *a
*a 55 mm (2.17 in.)
K108840

Foamed Sealing Material


Apply brushable seam seal on the foamed sealing material (1).

Expendable materials:
Brushable Seam Seal 310ml 08826-WA230



b.

Adjust and fix the front body pillar reinforcement lower.


c.

Weld the front body pillar reinforcement lower in areas (2) and (3).


d.
K152789

Weld the front body pillar reinforcement lower in areas (1).


e.
K152790

Apply brushable seam seal to A-pillar shaped part (1) and lower front A-pillar foamed sealing material (3).


f.

Install A-pillar shaped part (1) on lower left A-pillar reinforcement (2).


g.

Install lower front A-pillar foamed sealing material (3) in the new part of the outer section of A-pillar (4).


h.

Weld the side panel sub-assy outer in areas (3).

HINT:

Apply brushable seam seal to lower front A-pillar foamed sealing material (1) and A-pillar shaped part (2).


K152792C01
3.104,0.833 2.917,0.167 2.917,0.167 3.083,0.167 true 3.125,0.083 3.438,0.24 0.313,0.156 10 false *1
*1 SIDE PANEL SUB-ASSY OUTER - -
K108840

Foamed Sealing Material - -



i.

After welding, apply body sealer and undercoating to the corresponding parts. (See the painting/coating)


j.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.