Home › Vehicle Exterior › BODY PANEL › FRONT BODY PILLAR
BM3650E _01 Vehicle Exterior _083396 BODY PANEL _0402522 FRONT BODY PILLAR F

BODY PANEL  FRONT BODY PILLAR  CUT AND JOIN REPLACEMENT SECTIONS (PATTERN 1)  


K153141

REMOVE THE ADHESIVE


a.

Detach any mechanical connecting elements where required.


b.

Heat the adhesive flange with a hot air blower.

NOTICE:

Do not exceed the maximum object temperature of 250°C.



c.

Use pliers or a chisel to peel off the component.

NOTICE:

Do not damage adjacent components.



d.

Remove adhesive residue from the adhesive flange.



REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108826

Cut with Disc Sander etc.
K108827

Cut and Join Location

a.

Mark and perform the separating cuts to match the specified dimensions.

NOTICE:

Thereby disconnect only the outer panel.



b.

Remove the weld points in areas (1).


c.

Remove the weld points and adhesive in area (2).


d.

Remove the adhesive in area (3).


e.

Remove the side panel sub-assy outer from the foamed sealing material in areas (4).

K152773C01
3.344,1.281 3.167,0.417 3.167,0.417 3.333,0.417 false 3.604,0.573 3.917,0.729 0.313,0.156 10 false *a 3.885,3.5 4.198,3.656 0.313,0.156 10 false *b 5.073,3.417 5.281,3.615 0.208,0.198 10 false *b 2.25,0.219 2.563,0.375 0.313,0.156 10 false *a 3.375,0.344 3.688,0.5 0.313,0.156 10 false *1
*1 SIDE PANEL SUB-ASSY OUTER - -
*a 70 mm (2.76 in.) from the lower edge of the hole *b 80 mm (3.15 in.) from the upper edge of the hole
K108837

Adhesive
K108840

Foamed Sealing Material



f.
K152774

Remove the weld points in areas (1).


g.

Remove the weld points and adhesive in area (2).



INSTALL FOAMED SEALING MATERIAL


HINT:
·

Schematic diagram is for example purposes.

·

Some parts may differ in certain details.



a.
K152602

Clean the contact surface (1) with the cleaner R2.

Expendable materials:
Cleaner R2 500ml 08879-WA010



b.

On the contact surface (1), apply an approximately 15 mm bead (2) of brushable seam seal. If necessary apply a slightly thinner bead of brushable seam seal on each side, to prevent the sealant from running.

Expendable materials:
Brushable Seam Seal 310ml 08826-WA230



c.
K152775

Clean contact surfaces (1) using cleaner R2.

Expendable materials:
Cleaner R2 500ml 08879-WA010



d.

Apply brushable seam seal to the foamed sealing material in these areas (1).

Expendable materials:
Brushable Seam Seal 310ml 08826-WA230




INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108830

Fillet Weld
K108831

Butt Weld

a.

Position the side panel sub-assy outer.


b.

Weld the side panel sub-assy outer in areas (2).

K152776C01
3.635,0.667 3.417,0.25 3.417,0.25 3.25,0.25 false 3.063,0.167 3.375,0.323 0.313,0.156 10 false *1
*1 SIDE PANEL SUB-ASSY OUTER - -



c.
K152777C01
2.906,0.427 3.219,0.583 0.313,0.156 10 false *a 2.813,1.771 3.125,1.927 0.313,0.156 10 false *b
*a 50 mm (1.97 in.)
*b 30 mm (1.18 in.)


Weld the side panel sub-assy outer in areas (1) and (2).


d.

Apply seam seal in these areas (1).


e.

After welding, apply body sealer and undercoating to the corresponding parts. (See the painting/coating)


f.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.